Craftsman 113.225931 - Manual (Page 2)

FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER
If within drie year from the date of purchase^ this Craftsman Belt and Disc Sander fails due to a defect in
material or workmanship. Sears will repair it, free of qharge.^ ^ ^ ^
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE
OR SERVICE CENTER THROUGHOUT THE UNITED STATES. ; ^ ^
This warrarrty gives you specific legal rights, and you may also have other rights which vary from state to
state,
SEARS, ROEBUCK AND CO., Dept. 698/731A,
Sears
Tower, Chicago, IL 60684
gehéral safe instructions for power fools
1 . KNOW YOUR PÓWER TOOL ^ ^ ^
Read and : understand the owner's manual and labels
affixed to thè tool. Learn its application and limitations as
' well as the specific potential hazards peculiar tp this tòoi:-
2 GROUND ALL TOOLS
^ with an approved 3 conductor
grounding type plug to fit the proper
grounding type receptacle. The gieen conductor in the
cord is the.Vgrourrding Wire, Never connect the green wire
to a live terminal. ■
3. KEEP GUARDS IN PLACE
■ tn; vvóric íng. order, and rn proper adjustment and align
4 REMOVE ADJUSTING KEYS AND WRENCHES
^ Trsrm : habit : of checkirig. to see that keys and adjusting
vvrenches are-rernoveri trorn tool,before turning .it on.
5. KEEP WORK AREA CLEAN
. Cluttered, áréés and benches: invite accidents. Floor
must not be slippery due to wax or sawdust.
6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools n damps or wet locations ot ex .
;i'v,e them to tarn. Keep work aica well lighter!. Provide
. : ;a : ;r .;
7. KEEP CHILDREN AWAY
Ali visitors 5hóü(d}be:kepti-d:sated'staricellrdm.jWork a r e a , ,
8. MAKE WORKSHOP CHILD-PROOF
With pacifocks. masi(?i swilcfies, or t>y: rerriovinq starter
keys . • . ■ ■ '■ ■: ' • • ■. ■" •
9. DON'T FORCE TOOL
:: " it will do. the. job.:better and safer at the rate for Which .
it was designed : .. : .
10. USE RIGHT TOOL
Don't foice tool oi attachment to do a job. it was not
ciesigned f o r , . . .
It. WEAR PROPER APPAREL
Do not wear loose clothing, gltsves, neckties or jewelry
(rings, wristwatches) to get caught .in moving, parts, j
NONSLIP footwear is recommended. Wear protective,
hair covering to contain Song hair.. Roil long sleeves
above the elbow.
12. USE SAFETY GOGGLES (Head Protection)
Wear safety goggles (must cotrtply with ANSI Z87.Ì) at all
times; Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses. Also, use face or dust
mask if cutting operation is dusty, and ear protectors
(plugs or muffs) during extended periods of operation.
13. SECURE WORK
Use clamps or a vise to hold work when practical. It's
safer than using your hand, frees both hands to operate
: tool.
14. DON'T OVERREACH
Keep proper footing and balance at all times.
15 MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest perform­
ance. Follow instructions for lubricating and changing
accessories.
16. DISGONNECT TOOLS
before servicing, when changing accessories such as
blades, bits, cutters, etc.
17. AVOID ACCIDENTAL STARTING
Make sure switch is |n "OFF" position before plugging
in.
18. USE RECOMMENDED ACCESSORIES
: ; Cohsull the owner's manual for recommended accessories.
Follow the instructions that accompany the accessories.
" The use of improper accessories may cause hazards.
19. NEVER STAND ON TOOL
injury could occur if the too! is tipped or if the
cutting tool IS accidentally contacted.
Do not store materials above or near the tool such that
: It IS necessary to stand on the tool to reach them.
20. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that
IS damaged should be carefully checked to ensure that it
will operate property and perform rts intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other con-
ditioiis that may affect ns operation. A guard or other
part that IS damaged should be properly repaired or
replaced. .
21. DIRECTION OF FEED
Feed work into a blade or cutter against the direction of
rotation of the blade or cutter only.
22 NEVER LEAVE TOOL RUNNING
UNATTENDED
Turn power off. Don't leave tool until it comes to a
complete stop