Two Brothers Racing Yamaha Grizzly 700 - Manual (Page 2)

V.A.L.E.
V a r i a b l e a x i s l o c k i n g e x h a u s t
TM 2007 Yamaha
GRIZZLY 700
V.A.L.E.™ Slip-On Exhaust System with M-7 Aluminum Canister
Part # 005-1790406V
Installation Instructions
9. Align the mid-pipe with the ATV to ensure maximum
clearance and tighten the 4 V.A.L.E.™bolts.
10. Double check to make sure that all hardware is securely
tightened.
11. Re-install the mid=pipe joint cover.
12. Re-install all body parts listed in step 2.
13. Before you run the quad, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the quad and enjoy. It is normal for some white smoke
to appear the first time you start the quad. This is
packing/manufacturing oil from inside the pipe burning
off. Check for gaps or leaks. If you find a leak, a little
high temperature silicon sealant should fix it. After 50 to
100 miles, recheck all fasteners for tightness.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters at the first signs of packing material deterioration. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Qty. Description Part Number
1 Muffler Canister M-7 Aluminum 005-179-206M
1 Stainless Steel Slip-On Tube 005-17901S
1 HARDWARE KIT 005-179-3
1 X-Ring Kit 005-7-2-3KIT
2 Shim 005-106SR
1 8x25mm Flange Bolt 005-FB825
1 P1 Tip (installed) 005-P1
1 TBR Sticker Kit 015-10212
* Use the 2 shims supplied if you decide to remove
the already installed P1 PowerTip.