Two Brothers Racing Honda CB1000 - Manual

12. Before you run the bike, clean off all fingerprints and dirt, as
any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the bike and
enjoy. It is normal for some white smoke to appear the first
time you start the bike. This is packing/manufacturing oil
from inside the pipe burning off. Check for gaps or leaks.
If you find a leak, a little high temperature silicon sealant
should fix it. After 50 to 100 miles, recheck all fasteners for
tightness.
Parts List
IMPORTANT - PLEASE READ CAREFULLY
Installation
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on the sidestand
or ideally a rear service stand.
2. Remove OEM Muffler assembly. Retain mounting bolt for
later use.
3. Remove the OEM rubber grommet and sleeve from OEM
muffler mounting location. This will not be reused.
4. Remove right side rear passenger foot rest assembly.
5. Install TBR muffler mounting backet behind OEM
passenger foot rest and re-install on motorcycle.
6. Attach TBR slip-tube to TBR muffler using the supplied
6x20mm bolts and lock washers. Leave loose for now.
7. Slide barrel clamp over slip-tube joint and rubber lined
muffler clamp over muffler assembly.
8. Install on motorcycle and attach using the OEM muffler
mounting bolt.
9. Align muffler and tighten the 4 X-ring bolts.
10. Tighten muffler clamp and barrel clamp at slip-tube joint.
11. Double check all your work.
Qty. Description Part Number
1 Muffler Canister Varies
1 Slip-On Tube 005-28404S
1 Muffler Canister Clamp Varies
1 HARDWARE KIT 005-284-3
2 X-Ring (half) 005-7-2-3
4 6x14mm Socket Head Cap Screw 005-SH614
4 6mm Split Lock Washer 005-WL6
1 Mounting Bracket 005-284-B
1 64mm Barrel Clamp 005-27-64MSH
1 5mm Long Handle Ball End Hex Key 005-9-18610
1 T20 Torx Short Hex Key 005-9-15820
1 TBR Sticker Kit 015-10212
2009-10 Honda
CB1000R
Slip-on Exhaust System with M-2 Canister
Part # 005-2840406V / 005-2840407V / 005-2840408V
Care & Cleaning
We recommend that this performance part be installed by a qualified motorcycle
technician. If you have any doubts as to your ability to install this performance
part, please consult with your local motorcycle dealer. Read all instructions first
before starting installation. Make sure the motorcycle and exhaust system are
completely cool before starting the installation. Also, make sure the bike is secure
on a centerstand or ideally a service lift during installation. Be sure to save all stock
components for possible use later.
**This product has not been tested with all available accessories and some
items may cause excessive heat. Excessive heat may cause damage to your
vehicle. Two Brothers Racing will not be responsible for damaged parts.
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. For clean-
ing use a mild spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Stainless Header System: Polished stainless steel pipes will turn a light gold-
en hue after a few heat cycles, this is a normal characteristic of high quality
stainless steel.
Carbon Fiber Mufflers: Always make sure the fiberglass packing inside is in
good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the Carbon Fiber sleeve. TBR sells repack kits (TBR
part # 005-10038) that include new rivets and repack material as
well as a drill bit (#30), making it easy to do yourself. Also, NEV-
ER dyno test your bike with carbon fiber mufflers installed - the
intense heat and lack of cooling air can quickly cause the CF
material to burn. Two Brothers Racing does not provide a warranty for
burned carbon fiber.
Aluminum Mufflers: Use an aluminum or mag wheel polish such as Moth-
er’s to restore the bright finish to factory spec.