Great Plains YP4425A Material Rate - Manual (Page 3)

Great Plains Mfg., Inc. Cover iii
2014-05-13 Cover 401-627B
© Copyright 2007, 2008, 2009, 2010, 2011, 2012, 2014 All rights Reserved
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has
been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability
assumed for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and im-
prove its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the
future.
Trademarks of Great Plains Manufacturing, Inc. include: Singulator Plus, Swath Command, Terra-Tine.
Registered Trademarks of Great Plains Manufacturing, Inc. include:
Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone, Nutri-Pro, Seed-Lok, Solid Stand,
Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo Max, Turbo-Till, Ultra-Till, Verti-Till, Whirlfilter, Yield-Pro.
Brand and Product Names that appear and are owned by others are trademarks of their respective owners.
Printed in the United States of America
Table of Contents
Introduction ..................................................................1
Models Covered .............................................................1
Document Family ...........................................................1
Rate Setting Overview .................................................3
Setting Planting Rate......................................................3
Setting Fertilizer Rate.....................................................3
Population Reference Information..................................3
Kernels Per Pound .................................................3
Seeds per Unit............................................................3
Seed Spacing .............................................................3
Spacing (U.S. Customary units, page 1 of 2) .........4
Spacing (U.S. Customary units, page 2 of 2) .........5
Air-Pro
®
Meter Disk Selection ........................................6
Meter Pressurization ......................................................9
Initial Meter Pressurization: Round Corn................9
Initial Meter Pressurization: Canola and Cotton .....9
Initial Meter Pressurization: Milo.............................9
Initial Meter Pressurization: Soybeans ...................9
Initial Meter Pressurization: Sunflower ...................9
Initial Meter Pressurization: Volumetric ..................9
Initial Meter Pressurization: Flat Corn ..................10
Factory Default Air Control Channel Screens...........10
Material 16 Setup .................................................10
Control Channel 2 Setup ......................................10
Checking Planting Rate................................................11
Checking Singulated Rates ......................................11
Planting Rate ..............................................................13
Hydraulic Drive Meter Rate ..........................................13
Meter RPM Limit Charts ...............................................14
Meter RPM Limits: Corn 24 Cell ...............................14
Meter RPM Limits: Corn 40 Cell ...............................15
Meter RPM Limits: Cotton 60 Cell ............................16
Meter RPM Limits: Milo 65 Cell ................................17
Meter RPM Limits: Milo 130 Cell ..............................18
Meter RPM Limits: Soybeans 84 Cell.......................19
Meter RPM Limits: Soybeans 168 Cell.....................20
Meter RPM Limits: Sunflower 24 Cell.......................21
Sprocket Indexing (Stagger) .....................................22
Indexing Preparation ....................................................23
Basic Indexing ..............................................................23
Indexing Fine Adjustment.............................................25
Sprocket Indexing Charts .............................................26
Canola Seeding .......................................................... 29
General Information ..................................................... 29
Related Documents ..................................................... 29
Pre-Requisites ............................................................. 29
Prepare Meters ............................................................ 29
Loading Seed............................................................... 29
Configure Monitor ........................................................ 30
Material Setup .......................................................... 30
Material Setup: Hydraulic Drive............................ 30
Air-Pro
®
Meter RPM Limits: Canola ..................... 31
Channel Setup: Hydraulic Drive ............................... 32
Row Monitor Setup................................................... 33
Canola Field Update .................................................... 34
Tools Required......................................................... 34
Update Brushes ....................................................... 34
Loosen Meter ........................................................... 34
Update Seed Tube ................................................... 35
Volumetric Seeding ................................................... 36
General Information ..................................................... 36
Related Documents ..................................................... 36
Clean-Out Meters......................................................... 36
Check or Install Grain Shield ....................................... 37
Install Discs / Set Shutters ........................................... 37
Take Note of Meter Pressure ....................................... 37
Initial Meter Pressurization: Wheat ...................... 37
Initial Meter Pressurization: Rice.......................... 37
Calibrate....................................................................... 38
Furrow Checking Rate ................................................. 39
IntelliAg
®
Hydraulic Drive............................................. 40
Set Up A Material ..................................................... 41
Calibrate Speed Sensor ........................................... 45
Meter RPM Limits - Volumetric ................................ 46
RPM Limits: Rice.................................................. 46
RPM Limits: Wheat .............................................. 47
Fertilizer Rate ............................................................. 48
Fertilizer Rate Steps .................................................... 48
Orifice Plate Selection.................................................. 49
Determine Orifice Size ............................................. 49
Install Orifice Plates ................................................. 50
Row Shutoff.............................................................. 50
Strainer ........................................................................ 51