Tweco XT-301 Torch Data for OEM use w- Auto-Cut 30O2 AD - Manual (Page 25)

Manual 0-4832 Rev AD 8-25 TORCH DATA for AutoCut O
2
Stainless Steel
200A
Air Plasma / Air Shield
36-1018
36-1019
36-1281 36-1057 36-1085
36-1020
Shield
Retainer Shield Cup
Shield
Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor Electrode
Cartridge
Art # A-07597
36-1046 36-1029
(ga) (in) inch (PSI) Ball (PSI) Ball (PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
3/16 0.1875 56 90 110 Pressure 70 170 0.140 300 0.300 0 0.163
1/4 0.250 56 90 110 Pressure 70 173 0.140 275 0.300 0.1 0.162
3/8 0.375 56 90 110 Pressure 70 173 0.140 200 0.300 0.2 0.169
1/2 0.500 56 90 110 Pressure 70 175 0.140 145 0.350 0.3 0.169
5/8 0.625 56 90 110 Pressure 70 177 0.140 110 0.400 0.4 0.174
3/4 0.750 56 90 110 Pressure 70 179 0.160 80 0.450 0.5 0.176
7/8 0.875 56 90 110 Pressure 70 181 0.170 60 0.450 0.6 0.181
1 1.000 56 90 110 Pressure 70 184 0.180 45 0.500 1.1 0.181
1 1/4 1.250 56 90 110 Pressure 70 196 0.200 25 0.500 2 0.207
1 1/2 1.500 56 90 110 Pressure 70 204 0.200 15 0.220
2 2.000 56 90 110 Pressure 70 205 0.200 10 0.230
(Bar) Ball (Bar) Ball (Bar) Volts
(mm)
±0.1
(mm/min) (mm) (sec) (mm)
3.9 90 7.6 Pressure 4.8 170 3.6 7530 7.6 0 4.1
3.9 90 7.6 Pressure 4.8 173 3.6 7130 7.6 0.1 4.1
3.9 90 7.6 Pressure 4.8 173 3.6 6000 7.6 0.2 4.2
3.9 90 7.6 Pressure 4.8 175 3.6 4870 4.8 0.2 4.3
3.9 90 7.6 Pressure 4.8 177 3.6 3990 8.6 0.3 4.3
3.9 90 7.6 Pressure 4.8 179 3.6 3040 9.8 0.4 4.4
3.9 90 7.6 Pressure 4.8 181 4.4 1880 11.4 0.5 4.5
3.9 90 7.6 Pressure 4.8 184 4.5 1190 12.5 1 4.6
3.9 90 7.6 Pressure 4.8 196 5.1 630 12.7 1.9 5.3
3.9 90 7.6 Pressure 4.8 204 5.1 390 5.6
3.9 90 7.6 Pressure 4.8 205 5.1 250 5.8
8
5
10
6
Kerf Width
@ Rec.
Speed
Arc
Voltage
Initial
Piercing
Height
Pierce
Delay
Torch
Working
Height
25
Travel
Speed
Initial
Piercing
Height
200A Stainless Steel (Air/Air)
Cut Flow Rates / Pressures
Plasma (Air) Shield (Air)
Pierce
Delay
Material
Thickness
Arc
Voltage
Material
Thickness
Pre Flow
Pressure
(Air)
38
Kerf Width
@ Min/Max
Torch
Working
Height
Travel
Speed
Cut Flow Rates / Pressures
Shield (Air) Plasma (Air)
Edge Start
(mm)
32
Edge Start
50 Edge Start
15
20
12
Edge Start
Pre Flow
Pressure
(Air)