Triton TA 235CSL - Manual (Page 6)

5
GB
General Safety
• If a cut does not extend to the edge of the workpiece, or if the blade binds in
the cut, allow the blade to come to a complete stop and lift the saw out of the
workpiece
• Do not attempt to free a jammed blade before first disconnecting the machine
from power
• Do not move the saw backwards at any time whilst cutting
• Beware of projected waste. In some situations, waste material may be projected at
speed from the cutting tool. It is the user’s responsibility to ensure that other people
in the work area are protected from the possibility of projected waste
• If you are interrupted when operating the saw, complete the process and switch off
before diverting your attention
• The blade bolt and washers were specially designed for your saw. For optimum
performance and safety of operation never use damaged or incorrect bolt/blade
washers
• Check the lower guard for proper closing before each use. Do not operate the saw
if the lower guard does not move freely and close instantly. Never clamp or tie the
lower guard into the open position. If the saw is accidentally dropped, the lower
guard may be bent. Raise the lower guard with the retracting handle and make
sure it moves freely and does not touch the blade or any other part, in all angles
and depths of cut
• Always observe that the lower guard is covering the blade before resting the saw
on a surface after use. An unprotected, coasting blade will cause the saw to move
backwards, cutting whatever is in its path. Be aware of the time it takes for the
blade to stop after the trigger switch is released
• Periodically check that all nuts, bolts and other fixings have not loosened, tighten
where necessary
The tool must be used only for its prescribed purpose. Any use other than those
mentioned in this manual will be considered a case of misuse. The user, and not the
manufacturer, shall be liable for any damage or injury resulting from such cases of
misuse.
The manufacturer shall not be liable for any modifications made to the tool nor for any
damage resulting from such modifications.
Even when the tool is used as prescribed it is not possible to eliminate all residual risk
factors.
KICKBACK PREVENTION AND OPERATOR SAFETY:
Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an
uncontrolled saw to lift up and out of the workpiece toward the operator. Kickback is the
result of saw misuse and/or incorrect operating procedures or conditions and can be
avoided by taking precautions as follows:
a. Maintain a firm grip with both hands on the saw and position your arms to resist
kickback forces. Position your body to either side of the blade but not in line
with the blade. Kickback could cause the saw to jump backwards, however, if
precautions are taken, kickback forces can be controlled by the operator.
b. When the blade is binding, or when interrupting a cut for any reason, release the
trigger and hold the saw motionless in the workpiece until the blade comes to a
complete stop. Never attempt to remove the saw from the work or pull the saw
backward while the blade is in motion. Investigate and take corrective action to
eliminate the cause of blade binding.
c. When restarting a saw within an incomplete cut, centre the saw blade in the
kerf and check that the saw teeth are not engaged into the material (a binding
saw blade may ‘propel upwards’ or kickback from the workpiece as the tool is
restarted).
d. A large workpiece should be supported close to the line of the cut, and at the edge
of the panel, to prevent sagging. This will minimise the risk of blade pinching and
kickback.
e. Do not use dull or damaged blades. Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade binding and kickback.
f. Blade depth and bevel adjusting locking levers must be tight and secure before
making a cut. If blade adjustment shifts while cutting, it may cause binding and
kickback.
g. Use extra caution when making a ‘plunge cut’ into existing walls or other blind
areas. The protruding blade may cut objects causing kickback.
h. Check the lower guard before each use and do not use if it does not close freely,
ensuring that the blade does not touch any part of the guard or tool in all angles
and depths of cut. Never clamp or tie the lower guard in the open position.
i. Check the operation of the lower guard spring. If the guard and the spring are not
operating correctly, they must be serviced before use. The lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a build-up of debris.
j. The lower guard should be retracted manually only for special cuts such as ‘plunge
cuts’ and ‘compound cuts.’ Raise the lower guard by the retracting handle and as
soon as the blade enters the material, the lower guard must be released. For all
other sawing, the lower guard should operate automatically.
k. Ensure that the lower guard is covering the blade before placing the saw down.
An unprotected, coasting blade will cause the saw to ‘propel backwards’, cutting
whatever is in its path. Be aware of the time it takes for the blade to stop after the
switch is released. Do not use abrasive wheels, doing so will void the warranty.
l. If a circular saw features a riving knife it must be removed before plunge cutting. A
riving knife will interfere with a plunge cut causing kickback. The riving knife must
always be re-fitted after plunge cutting. A circular saw with
SAFETY RULES FOR LASER LIGHTS
The laser used in this device is a Class 2 laser with maximum power of ≤1mW and a
wavelength of 400-700nm.
These lasers do not normally present an optical hazard, although staring at the beam
may cause flash blindness.
WARNING: Avoid direct eye contact.
A hazard may exist if you deliberately stare into the beam, please observe all safety
rules as follows:
• The laser shall be used and maintained in accordance with the manufacturer’s
instructions
• Do not switch on the laser light until the tool is ready to cut
• Never aim the beam at any person, and particularly not into the eyes of any person
or animal, or any object other than the workpiece
• Always ensure the laser beam is aimed at a sturdy workpiece without reflective
surfaces. i.e. wood or rough-coated surfaces are acceptable. Reflective sheet steel
or similar is not suitable for laser use as the reflective surface could direct the
beam back at the operator
• Do not change the laser light assembly. Repairs must only be carried out by the
laser manufacturer or an authorised agent. DO NOT exchange with a different
type of laser
CAUTION: Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
Please refer to the relevant EN standards, EN60825-1/A1:2002 for more information
on Lasers.
a permanent, non-removable riving knife is NOT suitable for plunge cutting.
TA235CSL_Z5MANPRO1_V2.indd 5 06/11/2013 12:23