Banner Q60 Background Suppression Series - Manual (Page 9)

P/N 114348
9
Q60LAF Series Laser Adjustable-Field Sensors
Banner Engineering Corp. • Minneapolis MN, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Specifications
Supply Voltage and
Current
Q60BB6LAF models: 10 to 30V dc (10% maximum ripple) at less than 35 mA exclusive of load
Q60VR3LAF Universal models: 12 to 250V dc or 24 to 250V ac, 50/60 Hz
Input power 1.5 W maximum
Supply Protection
Protected against reverse polarity and transient voltages
(Q60VR3 models’ dc hookup is without regard to polarity)
Output Configuration
Q60BB6LAF models: Bipolar; one NPN (current sinking) and one PNP (current sourcing) open-collector
transistor
Q60VR3LAF cabled model: E/M Relay (SPDT), normally closed and normally open contacts
Q60VR3LAFQ1 (QD) model: E/M Relay (SPST), normally open contact
Output Rating
Q60BB6LAF models Q60BB6LAF models
150 mA maximum each output @ 25° C
Off-state leakage current: < 5µA @ 30V dc
Output sat u ra tion NPN: < 200 mV @ 10 mA and < 1V @150mA
Output sat u ra tion PNP: < 1V at 10 mA; < 1.5V at 150 mA
Q60VR3LAF Universal models
Q60VR3LAF Universal models
Min. voltage and current: 5V dc, 10 mA
Mechanical life of relay: 50,000,000 operations
Electrical life of relay at full resistive load: 100,000 operations
Max. switching power (resistive load): Cabled models: 1250VA, 150 W
QD models: 750VA, 90W
Max. switching voltage (resistive load): Cabled models: 250V ac, 125V dc QD models: 250V ac, 125V dc
Max. switching current (resistive load):
Cabled models: 5 A @ 250V ac, 5 A @ 30V dc derated to 200 mA @ 125V dc
QD models: 3 A @ 250V ac, 3 A @ 30V dc derated to 200 mA @ 125V dc
Output Protection
Circuitry
Q60BB6LAF models: Protected against continuous overload or short circuit of outputs
All models: Protected against false pulse on power-up
NOTE: 1 second max. delay at power up (outputs do not conduct during this time).
Output Response Time
Q60BB6LAF models: 2 milliseconds ON and OFF
Q60VR3LAF Universal models: 15 milliseconds ON and OFF
Repeatability 500 microseconds
Sensing Hysteresis See Figure 4.
Indicators (see Figure 1)
NOTE: Outputs are
active during
on/off timing
selection mode.
ON-Delay ON Green: RUN mode, ON-delay active
Flashing Green: ON-Delay Selection mode
OFF-Delay ON Green: RUN mode, OFF-delay active
Flashing Green: OFF-Delay Selection mode
5-Segment Light Bar*
ON/OFF-Delay Selection: Indicates relative delay time
RUN Mode:
Output ON Yellow: Outputs are conducting
ON Green: ON/OFF-Delay Selection
Dark Operate ON Green: Dark Operate selected
Lockout ON Green: Buttons locked out
Light Operate ON Green: Light Operate selected
Signal ON Green: Sensor receiving signal
Flashing Green: Marginal signal (1.0 to 2.25 excess gain)
Laser Characteristics
Spot Size: approximately 4 x 2 mm throughout range (collimated beam)
Angle of Divergence: 5 milliradians NOTE: Contact factory for custom laser spot size.