Beam diagrams, Wiring diagrams, Attention – Rockwell Automation 873P Ultrasonic Single & Dual Discrete Output Sensors Installation Instruction User Manual
Page 4: Important
Rockwell Automation 873P-IN003A-EN-P—October 2014
4 873P Ultrasonic Single & Dual Output Sensors
varies depending on the type(s) of sensors used (see below). The
target must be positioned at the same distance from each
synchronized sensor; the target position should overall be flat.
When mounted correctly, the synchronized sensors perform like a
single sensor with an extended detection angle.
Please note that sensor response times will increase
proportionally to the number of synchronized sensors.
How it Works:
Connect Pin 2 (white) to all sensors to be synchronized.
All sensors will trigger at the same time. Any eventual crosstalk
signal related to a longer sensing distance will be ignored. An
external synchronization pulse controls the sensors.
All minimum distances depend on target distance and material.
“T” is the pulse time period applied on the SYNC wire, and “Width”
refers to the pulse width.
• 400 mm Sensing Range Sensors
T ≥ 4 msec
500 μsec ≤ Width ≤ 1 msec
Minimum distance between sensors: 50
…
100 mm.
• 900 mm Sensing Range Sensors
T ≥ 7.5 msec
500 μsec ≤ Width ≤ 1 msec
Minimum distance between sensors: 30
…
50 mm.
• 2200 mm Sensing Range Sensors
T ≥ 17.5 msec
500 μsec ≤ Width ≤ 1 msec
Minimum distance between sensors: 30
…
40 mm.
• 2500 mm Sensing Range Sensors
T ≥ 25 msec
500 μsec ≤ Width ≤ 5 msec
Minimum distance between sensors: 100 mm for working
distances up to 1.5 m, and 50 mm for distances > 1.5 m.
• 3500 mm Sensing Range Sensors
T ≥ 35 msec
500 μsec ≤ Width ≤ 5 msec
Minimum distance between sensors: 100 mm for working
distances up to 1.5 m, and 50 mm for distances > 1.5 m.
• 6000 mm Sensing Range Sensors
T ≥ 60 msec
500 μsec ≤ Width ≤ 1 msec
Minimum distance between sensors is 200 mm for working
distances up to 1.5 m, and 50 mm for distances > 1.5 m.
Beam Diagrams
50…400 mm Sensing Range
Distance [mm (in.)]
0
100
(3.93)
200
(7.87)
300
(11.8)
400
(15.7)
500
(19.6)
Pa
rallel displac
emen
t [mm]
Target 25 mm dia.
Target 100*100 mm
Target 100*100 mm
Target 100*100 mm
Target 25 mm dia.
-100
-50
0
50
100
150
-150
Distance [mm (in.)]
0
200
(7.87)
400
(15.7)
600
(23.6)
800
(31.4)
1000
(39.3)
Pa
rallel displac
emen
t [mm]
-100
-50
0
50
100
150
-150
200
-200
Target 25 mm dia.
Target 200*200 mm
Target 200*200 mm
Target 200*200 mm
Target 25 mm dia.
100…900 mm Sensing Range
Wiring Diagrams
Distance [mm (in.)]
0
500
(19.68)
1000
(39.3)
1500
(59.0)
2000
(78.7)
2500
(98.4)
Pa
ra
llel displac
emen
t [mm]
-100
-50
0
50
100
150
-150
200
-200
Target 25 mm dia.
Target 200*200 mm
Target 200*200 mm
Target 200*200 mm
Target 25 mm dia.
250
-250
300
-300
Pa
ra
llel displac
emen
t [mm]
-100
-50
50
100
150
-150
200
-200
250
-250
300
-300
0
0
500
(19.6)
2000
(78.7)
3000
(118.1)
Distance [mm (in.)]
Target 25 mm dia.
Target 200*200 mm
Target 200*200 mm
Target 200*200 mm
Target 25 mm dia.
1000
(39.3)
2500
(98.4)
1500
(59.0)
200…2500 mm Sensing Range
200…2200 mm Sensing Range
Pa
rallel displac
emen
t [mm]
-100
-50
50
100
150
-150
200
-200
250
-250
300
-300
350
-350
400
-400
0
0
1000
(39.3)
2000
(78.7)
3000
(118.1)
4000
(157.4)
Distance [mm (in.)]
Target 25 mm dia.
Target 200*200 mm
Target 200*200 mm
Target 200*200 mm
Target 25 mm dia.
200…3500 mm
6000 mm
P
a
rallel displac
e
ment [mm]
7000
(275.6)
6000
(236.2)
5000
(196.8)
4000
(157.5)
3000
(118.1)
2000
(78.7)
1000
(39.4)
0
-600.0
-500.0
-400.0
-300.0
-200.0
-100.0
0.0
100.0
200.0
300.0
600.0
400.0
500.0
Distance [mm (in.)]
Target 200*200 mm
Target 200*200 mm
Target 400*400 mm
Target 400*400 mm
Single PNP Discrete Models
Dual PNP Discrete Models
Hold/
Sync
Hold/
Sync
Load
Load
Load
ATTENTION
If a hazardous condition can result from
unintended operation of this device, access to the
sensing area should be guarded.
Solid-state devices can be susceptible to radio
frequency (RF) interference depending on the
power and the frequency of the transmitting
source. If RF transmitting equipment is to be used
in the vicinity of the solid-state devices, thorough
testing should be performed to assure that
transmitter operation is restricted to a safe
operating distance from the sensor equipment and
its wiring.
IMPORTANT