Rockwell Automation 800T_TC Shallow, Mini and Sealed Contact Switch Blocks User Manual
Contact block mounting, E-doc
2943-99
12
1979-00
13
1000483
14
1
2
40060-226
REVISION
AUTHORIZATION
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
H
A
B
C
D
E
F
G
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
REFERENCE
SHEET
OF
DWG.
B
DR.
CHKD.
APPD.
DAT E
DAT E
DAT E
±
N/A
±
N/A
±
N/A
ANGLES:
.XXX:
.XX:
LOCATION : MILWAUKEE, WISCONSIN
U.S.A.
SIZE
1
2
3
4
5
6
7
8
E-DOC
FORM NO. 979 (10/94)
G. Ushakow
7/24/02
BULLETIN 800T
SHALLOW, MINI AND SEALED
CONTACT SWITCH BLOCKS
CONTENTS FOR INSTRUCTION SHEET
M. Jutz
7/24/02
R. Malecki
7/24/02
Contact Block Mounting
(Bulletin 800T and 800TC)
Block Type
Contact Block Circuit Identification
Circuit Symbol
Description
N.O.
3-4, A
N.C.
1-2, B
7-8, A
Z
5-6, B
Z
N.O. (Early Make)
N.C. (Late Break)
Identification
Cat No.
Comments
Wire Range
AWG
(mm
2
)
Tight Torque
lb-in
(Nm)
Standard
800T/TC-XD1, 2, 3, 4, 1V, 2V, 3V, 4V
800T/TC–XA, XA1, 2, 4, 7, V
Series A (large profile, no
longer available) Series B
& later (shallow profile)
14-18
(.5-2.5)
6-8
(.7-.9)
Mini
800T-XD5, 6
Requires special
screw provided with blocks
14-18
(.5-2.5)
6-8
(.7-.9)
MaxDuty
800T/TC-XD1M, -XD2M, -XD4M
High current.
Horsepower rated.
Short Circuit Rating: 5KA, 240VAC
when protected by fuses.
10-18
(.5-6.0)
6-8
(.7-.9)
Sealed — Hi Current
800T-XAP, XD1P, XD2P
14-18
(.5-2.5)
6-8
(.7-.9)
Sealed — Medium Current
800T-XAY, XA2Y, XA4Y
800T-XD1Y, XD2Y
Requires special screw
(extended head) provided
with blocks.
14-18
(.5-2.5)
6-8
(.7-.9)
Sealed — Logic Reed
800T-XAR, XA2R, XA4R
800T-XD1R, XD2R
14-18
(.5-2.5)
6-8
(.7-.9)
PenTUFF
800T/TC-XAV, XD1V, XD2V,
XD3V, XD4V
14-18
(.5-2.5)
6-8
(.7-.9)
Self Monitoring
800TC-XD4S
14-18
(.5-2.5)
6-8
(.7-.9)
Note: For two circuit contact blocks, it is recommended that the same wire size be used for each circuit.
Sealed Switch
Contact Block
Mounting Screw Torque
5-7 lb-in
Mini Contact Block
Extender
6-8 lb-in
(.7-.9 Nm)
Octagon Ring
Operator
Standard
& Self Monitoring
Contact Block
(Shallow Contact)
Spacer
(to be used on
operators without
4 corner posts)
(.55-.8 Nm)
Level 1
Level 2
Terminal Screw Torque
THIS DRAWING IS THE PROPERTY OF
ROCKWELL INTERNATIONAL CORPORATION
OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,
USED OR DISCLOSED FOR ANY PURPOSE
EXCEPT AS AUTHORIZED IN WRITING BY
ROCKWELL INTERNATIONAL CORPORATION