WINGITS Grab Bar SRGBW40 - Manual

W
ING
I
TS ® GBW40, GBW50, SRGBW40
World’s Strongest Fastener ™
Specifications
• GBW40 Standard WINGITS
® is used in walls framed with
2 x 4’s (3-1/2” hollow or larger). Comes with stainless steel 4”
screw for walls up to 1 1/4” thick.
• SRGBW40 Reverse WINGITS
® is used in walls framed with
2 x 3’s (2-1/2” hollow or larger).
• GBW50 Comes with stainless steel 5” screw for thicker walls.
NEVER INSTALL ANY FASTENER INTO WET OR DETERIORATING WALLS
Structural Blocking Must Be Used In PLAIN 1/2” DRYWALL When
Attempting To Meet Commercial Building Codes.
Commercial Grab Bar Fastening System Installation Guide
WINGITS
® Grab Bar Fastening Systems Exceeed Building Codes
For Grab Bars In The Following Wall Substrates:
• 5/8” Drywall - Painted or Wallpapered
• 1/2” or 5/8” Drywall with Tub Surrounds
• 1/2” or 5/8” Drywall with Tile, Marble or Stone
• 1/2” or 5/8” Drywall with any Panel Types including Fiberglass,
Faux Marble, Acrylic and Plastics
• Multiple Layers of Drywall, Plaster and Lathe
• 1/4” Acrylic/Fiberglass Tub Surrounds
• Most Wall Panels, All Masonry Type Boards
Before You Install:
ADAAG recommends Grab Bars be installed horizontally 33” - 36”
from the floor.
• Verify the length of the grab bar by measuring from the inside of
one flange to the outside of the other.
• To ensure adequate clearance, a stud finder should be used to
verify there are no studs within the area where the WingIts
® will
be installed. Make sure that there is at least 1.5” away from
the edge of the stud. If concerned, drill a pilot hole and insert
a piece of wire in the shape of an “L” - twirl the wire to make
sure there is nothing in the way. Once inserted, each wing
assembly will spring open almost 3” in diameter
• Tools Required: Screwdriver, 1.25” Drill
(our APACHE200 rated at 200 holes in ceramic wall tile)
W
ING
I
TS ® GBW40, GBW50, SRGBW40
World’s Strongest Fastener ™
GBW40
Specifications
• GBW40 Standard WINGITS
® is used in walls framed with
2 x 4’s (3-1/2” hollow or larger).
• SRGBW40 Reverse WINGITS
® is used in walls framed with
2 x 3’s (2-1/2” hollow or larger).
• WINGITS
®
come standard with a stainless steel 4” screw for walls
up to 1 1/4” thick. Larger screws available for thicker walls.
NEVER INSTALL ANY FASTENER INTO WET OR DETERIORATING WALLS
Structural Blocking Must Be Used In PLAIN 1/2” DRYWALL When
Attempting To Meet Commercial Building Codes.
Commercial Grab Bar Fastening System Installation Guide
WINGITS
® Grab Bar Fastening Systems Exceeed Building Codes
For Grab Bars In The Following Wall Substrates:
• 5/8” Drywall - Painted or Wallpapered
• 1/2” or 5/8” Drywall with Tub Surrounds
• 1/2” or 5/8” Drywall with Tile, Marble or Stone
• 1/2” or 5/8” Drywall with any Panel Types including Fiberglass,
Faux Marble, Acrylic and Plastics
• Multiple Layers of Drywall, Plaster and Lathe
• 1/4” Acrylic/Fiberglass Tub Surrounds
• Most Wall Panels, All Masonry Type Boards
Before You Install:
ADAAG recommends Grab Bars be installed horizontally 33” - 36”
from the floor.
• Verify the length of the grab bar by measuring from the inside of
one flange to the outside of the other.
• To ensure adequate clearance, a stud finder should be used to
verify there are no studs within the area where the WingIts
® will
be installed. Make sure that there is at least 1.5” away from
the edge of the stud. If concerned, drill a pilot hole and insert
a piece of wire in the shape of an “L” - twirl the wire to make
sure there is nothing in the way. Once inserted, each wing
assembly will spring open almost 3” in diameter
• Tools Required: Screwdriver, 1.25” Drill
(our APACHE200 rated at 200 holes in ceramic wall tile)
W
ING
I
TS ® GBW40, GBW50, SRGBW40
World’s Strongest Fastener ™
GBW40
Specifications
• GBW40 Standard WINGITS
® is used in walls framed with
2 x 4’s (3-1/2” hollow or larger).
• SRGBW40 Reverse WINGITS
® is used in walls framed with
2 x 3’s (2-1/2” hollow or larger).
• WINGITS
®
come standard with a stainless steel 4” screw for walls
up to 1 1/4” thick. Larger screws available for thicker walls.
NEVER INSTALL ANY FASTENER INTO WET OR DETERIORATING WALLS
Structural Blocking Must Be Used In PLAIN 1/2” DRYWALL When
Attempting To Meet Commercial Building Codes.
Commercial Grab Bar Fastening System Installation Guide
WINGITS
® Grab Bar Fastening Systems Exceeed Building Codes
For Grab Bars In The Following Wall Substrates:
• 5/8” Drywall - Painted or Wallpapered
• 1/2” or 5/8” Drywall with Tub Surrounds
• 1/2” or 5/8” Drywall with Tile, Marble or Stone
• 1/2” or 5/8” Drywall with any Panel Types including Fiberglass,
Faux Marble, Acrylic and Plastics
• Multiple Layers of Drywall, Plaster and Lathe
• 1/4” Acrylic/Fiberglass Tub Surrounds
• Most Wall Panels, All Masonry Type Boards
Before You Install:
ADAAG recommends Grab Bars be installed horizontally 33” - 36”
from the floor.
• Verify the length of the grab bar by measuring from the inside of
one flange to the outside of the other.
• To ensure adequate clearance, a stud finder should be used to
verify there are no studs within the area where the WingIts
® will
be installed. Make sure that there is at least 1.5” away from
the edge of the stud. If concerned, drill a pilot hole and insert
a piece of wire in the shape of an “L” - twirl the wire to make
sure there is nothing in the way. Once inserted, each wing
assembly will spring open almost 3” in diameter
• Tools Required: Screwdriver, 1.25” Drill
(our APACHE200 rated at 200 holes in ceramic wall tile)
GBW40