MTS Model 493-04 PC-Per-Station Kit User Manual
Page 19
How to Use PC-Per-Station Networking
MTS Model 493.04 PC-Per-Station-Kit
19
About Older PC-Per-Station Installations with Network Hubs
Older PC-Per-Station installations use a network hub configured as shown below.
Note
Hubs only support hal-duplex communications.
1. Use the existing “crossover” cable to connect the controller processor
module to the Uplink/Normal (MDI/MDIX) port (usually port 8) of the
controller-dedicated network hub.
The Uplink/Normal (MDI/MDIX) port LED (usually port 8) should
illuminate when the connection has been established. If the LED does not
illuminate, press the Uplink/Normal (MDI/MDIX) port switch located on
the back of the hub.
2. Connect the controller-dedicated network hub to the built-in Ethernet
network adapters in the PCs.
Note
Make sure everyone using your system controller can identify the master
PC. You must apply power to the master PC to use controller software
applications on the dependent PCs.
1
2
3
4
5
6
7
8
MDIX
Switch
Port 8 To controller processor
Ports 1-7 To built-in PC Ethernet connectors
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)