Crosshead method – MTS Criterion 40 - Lifting and Moving Instructions User Manual
Page 16
Moving C43 (30 kN, 50 kN) and C44 Frames
MTS Criterion
®
Series 40 Lifting and Moving Instructions
16
7. Before placing the frame in its operating location, you must insert the
leveling feet into each corner of the base. The shipping skid must be
removed to insert the feet and before placing the frame in its operating
location. Remove the shipping skid, insert the leveling feet, and position the
frame. Follow the instructions described under
“Crosshead method”
on page
16.
When the frame is in its operating location, you can proceed with the installation
process.
Lifting the Frame from the Base
Crosshead method
This method requires protective padding on either the crosshead or forklift arms
to protect the crosshead from scratching or marring.
This method can be used to:
•
Transport the load frame to the site location.
•
Lift a tabletop load frame onto a table or workbench.
•
Lift the frame to remove the transport skid from the frame’s base and to
insert the leveling feet.
Load Frame
Shipping Bolt
Shipping Skid
Forklift Arm
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)