Mk-5000g product specification, Engine owner's manual, Warranty card – MK Diamond MK-5000 Gas User Manual
Page 11

11
MK-5000G PrODUCT sPeCiFiCaTiON
The MK-5000G is not designed to cut plastic or ferrous (metals) material.
NOTe:
Your MK-5000G has been shipped from the factory thoroughly inspected. Only minimal assembly is
required. If not done, completely remove the plastic wrapping from the MK-5000G. Remove the ac-
cessories box from the Water Basin and remove the contents from the box.
MK-5000G
Block Saw
Movable Cutting
Table
Cutting Guide
Drain Plug
Blade Wrench
Owner's Manual
09.2009
MK-5009G/5013G
OWNERS MANUAL
PARTS LIST &
OPERATING INSTRUCTIONS
www.mkdiamond.com
MK Diamond Products, Inc.
Caution: Read all safety and operating instructions before
using this equipment. This parts list
MUST accompany the
equipment at all times.
Revision 100
Manual Part# 160958
Engine Owner's
Manual
Name
address
City
state
zip Code
phoNe
Fax
produCt model
part NumBer
maChiNe serial#
MK DiaMonD Warranty CarD
q
tile distriButor
q
home CeNter
q
equipmeNt supply house
q
tool supply
q
Bldg material supply
q
reNtal equipmeNt house
are you a do-it-yourselFer
q
or CoNtraCtor
q
I
F so, what type? tile
q
masoNry
q
other
what Criteria was importaNt iN ChoosiNg this saw? (rate From 1 to 5, 5 BeiNg the most importaNt)
power
preCisioN
portaBility
availaBility
other
If within one (1) Year from the date of purchase, this MK Diamond saw fails due to defect in material or workmanship, MK will repair it, free of charge when the unit is re-
turned to the dealer where it was purchased. This warranty DOES NOT cover normal wear or damage resulting from operator abuse. In no event shall MK Diamond Products,
Inc. be liable for consequential damages arising out of the failure of any product if operated improperly. MK Diamond Products may act as a warranty station for motor/en-
gine repairs based on an individual agreement with the manufacturer. This warranty is in lieu of all other warranties express or implied.
©2010 All Rights reserved. MK Diamond Products, Inc. • P/N 155037 MK Warranty Card (02/10)
mK diamoNd warraNty
1315 Storm Parkway, Torrance, CA 90509 USA | www.mkdiamond.com | 1.800.421.5830 | 1.310.539.5158
where did you purChase this saw From? Name
CommeNts or suggestioNs:
priCe
date purChased
Warranty Card
UNPaCKiNG
CONTeNTs
In your container, you will find one (1) MK-5000G, one (1) movable cutting table, one (1) adjustable
cutting guide, one (1) drain plug, one (1) blade wrench, one (1) owner’s manual, one (1) Engine
owner’s manual and one (1) warranty card.
Masonry Types
The MK-5000G can cut a variety of masonry types including, cinder block, slump stone block, wall
brick, paver brick, concrete block and cylinders, roofing tile, marble, granite, decorative rock or almost
any other non-ferrous material.
spring assisted Cutting Head
The MK-5000G is designed with a spring-assisted cutting head to allow for easier step cutting. The
Cutting Head can be locked in the down position when cutting smaller pieces.
shaft Operated Water Pump
The MK-5000G has a flexible shaft, belt driven water pump supplying cooling water to the blade for
wet cutting operations.