Festo DAPS..R..-F.. - Manual (Page 6)

10 Eliminating faults
• Please contact Festo.
11 Technical specifications
Size Single-acting drives Double-acting drives
Switching time per cycle
1)
[s] Switching time per cycle
1)
[s]
DAPS-0008-... – 0.08
DAPS-0015-... 0.2 0.08
DAPS-0030-... 0.5 0.13
DAPS-0053-... 0.9 –
DAPS-0060-... – 0.2
DAPS-0090-... 1.3 –
DAPS-0106-... – 0.4
DAPS-0120-... 1.7 –
DAPS-0180-... 2.7 0.6
DAPS-0240-... 3.7 0.8
DAPS-0360-... 3.9 1.2
DAPS-0480-... 3.1 1.6
DAPS-0720-... 5.8 2.7
DAPS-0960-... 6.3 3.1
DAPS-1440-... 19.0 5.5
DAPS-1920-... 15.0 6.0
DAPS-2880-... 19.0 16.0
DAPS-3840-... – 12.0
DAPS-4000-... 25.0 –
DAPS-5760-... – 16.0
DAPS-8000-... – 22.0
1) The switching times are specified in seconds and represent average values under idling conditions
Operating conditions DAPS
double-acting DAPS-
0008 DAPS-
0015 …
0360 DAPS-
0480 …
1920 DAPS-
2880 …
5760 DAPS-
8000
Work pressure 1) [bar] 2.8 ... 8.4 1 ... 7
Rated operating pressure [bar] 5.6
Operating medium Compressed air to ISO 8573-1:2010 [7:4:4]
Note on the operating medium Lubricated operation possible (required for continued
operation)
Ambient temperature [°C] –20°C … +80
ATEX ambient temperature [°C] –20°C ≤ Ta ≤ +60
Swivel angle [°] 90
End-position adjusting
range at 0° [°] – – – ±5
End-position adjusting
range at 90° [°] – ±2 ±2 ±5
Mounting position as desired
Tubing dia. = 8 mm
Materials
Drive shaft high-alloy steel
Cover wrought aluminium alloy
Housing wrought aluminium alloy
1) Exceptions for devices with special marking
Operating conditions DAPS
single-acting DAPS-
0015 …
0180 DAPS-
0240 …
0960 DAPS-
1440 …
1920 DAPS-
2880,
4000
Work pressure
1)
[bar] 2.8 ... 8.4
Rated operating pressure [bar] 5.6
Operating medium Compressed air to ISO 8573-1:2010 [7:4:4]
Note on the operating medium Lubricated operation possible (required for continued
operation)
Ambient temperature [°C] –20°C … +80
ATEX ambient temperature [°C] –20°C ≤ Ta ≤ +60
Swivel angle [°] 90
End-position adjusting
range at 0° [°] – – – ±5
End-position adjusting
range at 90° [°] ±2 ±2 ±2 ±5
Mounting position as desired
Tubing dia. = 8 mm
Materials
Drive shaft high-alloy steel
Cover wrought aluminium alloy
Housing wrought aluminium alloy
1) Minimum operating pressures vary for single-acting quarter turn actuators depending upon spring
quantity