EUCHNER GPxxx - Manual (Page 5)

Operating Instructions Safety Switch GP...
EUCHNER GmbH + Co. KG Kohlhammerstraße 16 D-70771 Leinfelden-Echterdingen Tel. +49/711/75 97-0 Fax +49/711/75 33 16 www.euchner.de [email protected]
Inspection and service
If damage or wear is found, the complete switch
and actuator assembly must be replaced.
Replacement of individual parts or assemblies
is not permitted!
No servicing is required, but regular inspection of
the following is necessary to ensure trouble-free long-
term operation:
correct switching function
secure mounting of components
dirt and wear
sealing of cable entry
loose cable connections or plug connectors.
Note:The year of manufacture can be seen in the
bottom, right corner of the rating plate.
Exclusion of liability under the following
circumstances
incorrect use
non-compliance with safety regulations
installation and electrical connection not performed
by authorized personnel.
failure to perform functional checks.
Subject to technical modifications; no r
esponsibility is accepted for the accuracy of this information. © EUCHNER GmbH + Co. KG
090205-06-10/10 (translation of the original operating instructions)
34 34
42 42
22 22
12 12
12 12
22 22
42 42
34 34
14
22 22
42 42
34 34
21 22
14 13
11 12
22 21 22
12
14
22
21
11
13
21
41 42
34 33
33
41
21
11
22 21
11 12
12 11
21 22
11
21
41
33
33 34
42 41
14 13
21 22
13
21
41
33
33 34
42 41
1 2
3
4 5
6
4 5
6
7
8
11 9
3
2
1
10
PE
Type Switching contacts
GP.-528H... 1 NC contact + 1 NO contact
GP.-538H... 2 NC contacts
GP.-2121H... 4 NC contacts
GP.-2131H... 3 NC contact + 1 NO contact
GP.-3131H... 2 NC contact + 2 NO contact
Door closed Door open
Plug connector
SR6
Plug connector
SR11
2.
1
2.
2
3 4
1. 1.
6 5
Ordinal numbers of
switching elements
2.
1. 1.
2.
3. 3.
4. 4.
6
8
5
7
4 3
2 1
Ordinal numbers of
switching elements
Terminal assignment with
plug connector
Connector
illustration
(view of safety switch
connection side)
(LED indicator with full wiring options, optional)
Figure 3: Switching elements and switching functions
EC declaration of conformity
The manufacturer named below herewith declares that
the product fulfills the provisions of the directive(s)
listed below and that the related standards have been
applied.
EUCHNER GmbH + Co. KG
Kohlhammerstraße 16
70771 Leinfelden-Echterdingen, Germany
Directives applied:
Machinery directive 2006/42/EC
Standards applied:
EN 60947-5-1:2004 + Cor.:2005 + A1:2009
EN 1088:1995+A2:2008
Leinfelden, July 2010
Dipl.-Ing. Michael Euchner
Director
Duc Binh Nguyen
Authorized representative empowered to draw up
documentation
The signed EC declaration of conformity is included
with the product.
Technical data
Parameters Value
Housing material Reinforced thermoplastic
Degree of protection according to IEC 60529
GP1...
IP67
GP2... IP65
Mechanical life 2x10 6 operations
Ambient temperature -20 ... +80°C
Degree of contamination
(external, according
3 (industrial)
to EN 60947-1)
Installation position
Any
Approach speed, max. 20 m/min
Actuating force 10 N
Actuation frequency, max. 6700 / h
Extraction force 20 N
Retention force 2 N
Switching principle Slow-action switching contact
Contact material Silver alloy, gold flashed
Connection type
GP1...
Screw terminal
GP2...SR6 Plug connector SR6, 6-pin+PE
GP2...SR11 Plug connector SR11, 11-pin+PE
Conductor cross-section (rigid/flexible)
GP1...
max. 1.5 mm²
GP2...SR6 0.5...1.5 mm²
GP2...SR11 0.5 mm²
Operating voltage for L060 12 - 60 V
optional LED indicator L110 110 V
(GP...528H/GP...538H only) L220 230 V
Switching voltage min.
12 V
at 10 mA
Switching current, min.,
at 24 V
1 mA
Short circuit protection (control
4 A gG
circuit fuse) acc. to IEC 60269-1
Conv. thermal current I
th
4 A
Utilization category
GP1.../GP2...SR6 GP2...SR11
according to EN 60947-1-5
AC-15
4 A 230 V 4 A 50 V
DC-13 4 A 24 V 4 A 24 V
Rated impulse
U
imp
= 2.5 kV U
imp
= 1.5 kV
withstand voltage
Rated
U
i
= 250 V U
i
= 50 V
insulation voltage
Rated short-circuit current
100 A
Reliability figures according to EN ISO 13849-1
B
10d 3 x 10 6