ETC Desire Series XTI User Manual
E t c, Selador desire, Series d40/d60 xti
E T C
®
I n s t a l l a t i o n G u i d e
Selador Desire
®
Series D40/D60 XTI
D40/D60 XTI
Page 1 of 4
Electronic Theatre Controls, Inc.
Corporate Headquarters
3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA
Tel +608 831 4116
Fax +608 836 1736
London, UK
Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK
Tel +44 (0)20 8896 1000
Fax +44 (0)20 8896 2000
Rome, IT
Via Pieve Torina, 48, 00156 Rome, Italy
Tel +39 (06) 32 111 683
Fax +44 (0) 20 8752 8486
Holzkirchen, DE
Ohmstrasse 3, 83607 Holzkirchen, Germany
Tel +49 (80 24) 47 00-0
Fax +49 (80 24) 47 00-3 00
Hong Kong
Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong
Tel +852 2799 1220
Fax +852 2799 9325
Service: (Americas)
(UK)
(DE)
(Asia)
Web:
Copyright © 2014 ETC. All Rights Reserved.
Product information and specifications subject to change.
7410M2100
Rev B
Released 2014-02
ETC intends this document to be provided in its entirety.
Overview
Specifications
Environment
Operates in ambient temperatures of -20°C to +40°C.
Control
The Desire XTI fixtures are provided with a 6’ (1.8m) bare-end Cat5 data
cable with braided shield for connection to a DMX/RDM control network.
A termination board is provided separately for installation into a voltage
separated junction box (provided by others) and provides termination for
control wiring.
• Connection of the Desire XTI data cable to a provided Insulation
Displacement Connector (IDC). The braided shield connects to the
termination board strain relief for ground.
• Connection of DMX/RDM input from the control source. This connection can be cable type Belden
9729 (or equivalent) to the provided screw terminal. When using Cat5 (or equivalent) cable type
for DMX/RDM input, order a Cat5 termination kit from ETC (part number 4100A1013). Cat5
termination instructions and an IDC connector are provided with the termination kit.
• Connection of DMX/RDM thru to the next DMX device. This connection may also be either Belden
9729 or Cat5. Order the appropriate DMX termination kit for the cable type used from ETC (Belden
9729 use 4100A1012 or Cat5 use 4100A1013). Termination instructions and the appropriate
connector is provided with the termination kit. Up to 32 DMX/RDM devices can be daisy-chained
together per data run.
C A U T I O N :
Do not attempt to install or use a fixture until you read and understand the installation
instructions and safety labels.
W A R N I N G :
This fixture must be installed by a qualified electrician in accordance with all
national and local electrical and construction codes and regulations.
C A U T I O N :
• Risk of eye injury. Do not stare directly into the light.
• Do not operate in proximity to flammable materials.
ETC’s D40XTI and D60XTI fixtures are
designed for permanent installation indoors or
outdoors, with IP66 rating, a rugged die-cast
enclosure, stainless steel mounting yoke, and
noiseless fan-free operation.
The Desire XTI fixtures can be pipe mounted
with a c-clamp, pole mounted, wall mounted, or
installed to a permanent base. Mounting
accessories are available. Contact ETC
Customer Service for assistance; contact
information is located at the bottom of this
page.
D40XTI
D60XTI
ON
OFF
Termination
J1 DMX In
DMX Thru