ETC Source Four XT HID Zoom External Media Holder - Manual

Corporate Headquarters 3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA Tel +608 831 4116 Fax +608 836 1736
London, UK Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK Tel +44 (0)20 8896 1000 Fax +44 (0)20 8896 2000
Rome, IT Via Pieve Torina, 48, 00156 Rome, Italy Tel +39 (06) 32 111 683 Fax +44 (0) 20 8752 8486
Holzkirchen, DE Ohmstrasse 3, 83607 Holzkirchen, Germany Tel +49 (80 24) 47 00-0 Fax +49 (80 24) 47 00-3 00
Hong Kong Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong Tel +852 2799 1220 Fax +852 2799 9325
Service: (Americas)
[email protected] (UK) [email protected] (DE) [email protected] (Asia) [email protected]
Web: www.etcconnect.com Copyright © 2011 ETC. All Rights Reserved. Product information and specifications subject to change.
7065M2140 Rev A Released 2011-08
ETC intends this document to be provided in its entirety.
Page 1 of 2
Installation Instructions
Source Four XT HID Zoom External Media Holder
The Source Four XT HID Zoom external media holder is used to attach up to two dichroic lenses and multiple sheet filter
media (gel). This allows you to add temporary media to the fixture for seasonal or special occasions.
The External Media Holder consists of the following.
● Front ring with four stainless hex screws
● Two solid spacers
● Split gel frame ring
The External Media Holder can remain on the fixture without media. One solid spacer may be removed to allow an
additional dichroic lens or a clear glass lens to be installed. Acceptable lens sizes are 7-7/16 to 7-3/4 inches (188 to
198mm) diameter.
Reference Source Four XT HID Installation Instructions and Source Four XT HID Long Yoke Installation Instructions for
information about electrical requirements and installing the fixture. Both instructions include a full-sized yoke template
and are available for download at www.etcconnect.com.
Installation
To install the External Media Holder with sheet filter media:
Step 1: Using the ring as a template, cut the sheet filter media (gel) 7-7/16 to 7-3/4 inches (188 to 198mm) to fit the split
gel frame ring. Then insert the media into the split gel frame ring.
Step 2: Lay the front ring face down.
Step 3: Optional: Insert a clear tempered glass lens (by others) into the front ring.
Step 4: Insert a spacer, the assembled gel frame ring, and the other spacer. Refer to the illustration on the next page.
Step 5: While holding the media holder assembly together, align the four holes on the holder with the holes on the front
of the fixture with the front ring facing away from the fixture.
Step 6: Attach the media holder with the provided four hex screws.
WARNING:
● Do not use this fixture with a damaged power lead. If the power lead (cordset)
is damaged, it must be replaced.
● Do not expose the interior of the fixture to moisture. Do not stand in water
while installing or servicing the fixture.
Failure to follow these warnings can result in serious injury or death.
WARNING:
● Do not use the fixture with a damaged power lead. If the power lead (cordset) is
damaged, it must be replaced.
● Do not expose the interior of the fixture to moisture. Do not stand in water while
installing or servicing the fixture.
Failure to follow these warnings can result in serious injury or death.
WARNING:
● Do not use the fixture if glass lens is deeply scratched or cracked. Damaged lenses
must be replaced.
● Do not mount the fixture on or near combustible surfaces.
Failure to follow these warnings can result in serious injury or death.