Anchor NAVI-TRAC LITE 30 WIDE - Manual (Page 15)

15
APPENDIX #1
(GABLED-HIP) AND
(GABLED-GABLED) END UNITS
GABLED-HIP END
FRAME
In the Hip-Gable construction, the hip end should be built first
to provide stability to the structure. Then, using the same tech-
niques as shown earlier, continue standing middle beams as
desired.
At the final end beam, be sure to attach the Gabled End Rafter
Fittings and the End Uprights themselves before standing the
beam (see fig. 48)
Notice that all 30’ wide Gabled ends require the X-cabling of the
end bay (see fig. 47). Also, when the structure exceeds 60 ft
of length, and additional X-Cabled bay is required (see fig. 58).
Parts for the Gabled End construction are listed below. For
assembly procedure, see the top of page 20.
GABLED-HIP END UNITS
47
X-Cabling stabilizes
the Gabled End Bay
COMPONENT CHART
PARTS FOR 30’ HIP-GABLED PER PER
LABEL OR GABLED-GABLED UNITS 30’ 10’
(LETTER (GABLED COMPONENTS IN ITALICS) POSITION ID PART GBL END EXTENSION MID
ON DWG) COMPONENT DESCRIPTION CODE CODE # KIT (#1358) KIT (#1356)
TOP EXTRUSIONS WITH CHANNELS:
E-15 EAVE - 15’ 8004410 0 2
RG-15 RIDGE W/ HOOKS - 15’ 8004415 0 1
R-30 RAFTER 30’ WHITE BRACE HOLE 8004440 0 2
EE-10 GABLED END MID EAVE - 10’ 8004475 1 0
EW-10 GABLED END WING EAVE - 10’ 8004460 2 0
GU GABLED END UPRIGHT W/ TOP FITTING 8004465 2 0
PURLINS AND BRACES:
P-10 PURLIN , 10 ’ [ For 30’ Clearspans & Reduced Bays only ] 80410 0 [2]
P-15 PURLIN, 15’ 80420 0 2
RB RIDGE BRACE 3580660 0 1
GRB GABLED END RIDGE BRACE 3580662 1 0
UPRIGHTS:
U-8 UPRIGHT - 8’ 8004450 0 2
WELDMENTS, FITTINGS & PLATES:
BA BASEPLATES, ADJUSTABLE, 2-HOLED 8004505 0 2
BAG BASE PLATE, GABLED END, ADJ, 2-HOLED 8004510 2 0
RW RIDGE WELDMENTS ASSEMBLY 8004545 0 1
EW EAVE WELDMENT W/ PINS 8004530 0 2
GWL GABLED END WELDMENT (L) 8004535 1 0
GWR GABLED END WELDMENT (R) 8004540 1 0
GRFL & R GABLED END RAFTER FITTINGS [L & R] 8004470 1 PAIR 0
TP TENSION LOCK PIN 3102865 2 2
CABLES
X8-15 X-CABLE, 8’ UPRIGHT 15’ BAY GREEN NAVLTCS-BAY15-U8 8004560 4 0 (unless over 60’ L)
X9-15 X-CABLE, 9’ UPRIGHT 15’ BAY (FOR CS ONLY) GREEN NAVLTCS-BAY15-U9 8004590 [4] 0
X10-15 X-CABLE, 10’ UPRIGHT 15’ BAY (FOR CS ONLY) GREEN NAVLTCS-BAY15-U10 8004500 [4] 0
XR-15 X-CABLE, RAFTER, 15’ BAY BLUE NAVLT-BAY15 8004570 4 0
*
*
The top fitting on the GU must be slid out of the upright so it is pinned in the second hole.