JLG G12-55A AccuPlace Operator Manual - Manual (Page 27)

Section 2 - Pre-Operation and Inspection
2-3 3128447
2.2 SAFETY DECALS
Ensure all DANGER, WARNING, CAUTION and instructional decals and proper
capacity charts are legible and in place. Clean and replace as required.
OY1260
91503108
9150-3108 REV -
M O V I N G PA RT S c o u l d c r u s h c a u s i n g d e a t h o r s e r i o u s i n j u r y.
K e e p c l e a r o f w h e e l s a n d m o v i n g p a r t s w h i l e e n g i n e i s r u n n i n g .
91503108
9150-3108 REV -
M O V I N G PA RT S c o u l d c r u s h c a u s i n g d e a t h o r s e r i o u s i n j u r y.
K e e p c l e a r o f w h e e l s a n d m o v i n g p a r t s w h i l e e n g i n e i s r u n n i n g .
91503109
9150-3109 REV -
N O R I D E R S . R i d e r s c o u l d FA L L O F F m a c h i n e c a u s i n g d e a t h o r s e r i o u s i n j u r y.
DO NOT use Ether or other high energy starting aids.
Engine equipped with
Pre-heating system.
ENGINE EXPLOSION could result in death or serious injury.
1706300C
1706300 1705881
91503110
CONTACTING ELECTRIC POWER L I N E S w i l l r e s u l t i n d e a t h o r s e r i o u s i n j u r y.
D o n o t p l a c e m a c h i n e o r l o a d w i t h i n 1 0 f e e t ( 3 m ) o f e l e c t r i c
9150-3110 REV - A p o w e r l i n e s .
10 FT. (3 M)
1
2
3
4
GEAR
9156-3246 REV A
D o w n - s h i f t t o a l o w e r g e a r w h e n d e s c e n d i n g . O v e r s p e e d i n g o f d r i v e t r a i n c o u l d r e s u l t i n e q u i p m e n t d a m a g e o r p e r s o n a l i n j u r y .
91563246
91503098
9150-3098 REV. A
For safe operation of machine, and to minimize risk of s e r i o u s i n j u r y, R E A D A N D O B S E RV E t h e f o l l o w i n g :
6. Keep others away from machine when operating. Do not allow others to stand under boom or load. Always look in direction of travel.
7. Use extreme care when handling long, high or wide loads. Do not handle unstable or loosely stacked loads.
8. Forks must be centered under load, and spaced apart as far as possible.
9. Level machine before lifting any load above 4 feet (1.2m).
10. Improper use of machine could result in machine tipping over. If machine starts to tip over, do not leave operator's seat. Lean away from tip, and brace yourself. 11. Keep mirror(s) clean and properly adjusted. Objects in mirror(s) are closer than they appear.
5. On inclines, travel with load up-grade.
1. Only trained and authorized personnel may operate this machine.
2. Before operating, read and understand all capacity charts, operator manual and safety manuals.
3. Operator must be seated with seat belt fastened. Assure all controls are in neutral before ignition switch is turned on.
4. Do not travel with boom raised. When traveling, fully retract boom and place forks in carry position, which is approximately 4 feet (1.2 m) above ground. Tilt carriage back slightly to cradle load. Use extreme caution when turning.
91513208
9151-3208 REV -
When lifting personnel, USE ONLY a Gradall manufactured personnel work platform, with proper personnel work platform CAPACITY CHART DISPLAYED in cab.
READ AND UNDERSTAND personnel work platform Owner/Operator manual before lifting personnel. DO NOT DRIVE machine from cab when personnel are on platform.
All personnel on platform must WEAR A FULL BODY HARNESS, with lanyard attached to a designated anchorage point.
When personnel are on platform, the OPERATOR MUST REMAIN SEATED in cab with personnel in direct line of sight. OPERATE CONTROLS CAUTIOUSLY and lightly when lifting or positioning personnel.
Failure to comply could result in death or serious injury.
1001100999
1001100999 A
1001100996
1001100996 A
1707038
1707038D
1001100998
1001100998 A