Smittybilt 76837 XRC Fender Flares - Manual (Page 3)

WWW.SMITTYBILT.COM
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
XRC Fender Flares
07-10 Wrangler & Unlimited
(Part # 76837)
Driver Side
Step 7: Hold new flare up against body, lining up the holes in the flare with the holes in the body.
Loosely attach using 2 of the included 10mm bolts, 4 flat washers and 2 nuts. Position flare into
the best fitment location and then securely tighten all hardware. (Fig B) Due to some variations in
hole locations on the vehicles you may need to slightly enlarge holes with a drill. Use caution when
drilling.
Step 8:
After top two bolts are secured, install the self-tapping screws into the 5 remaining holes. Be
careful not to over-tighten
Note:
With some effort you can re-use the inner liners. This would require precise trimming and secure
with the previously removed hardware form Step 1 and some large O.D. flat washers.
Installation is now complete
LIMITED WARRANTY
Smittybilt (The Company) warrants to the original purchaser of this product that should the product or any part thereof, under normal use and conditions, be proven
defective in material or workmanship within 5 years from the original date of purchase, such defect(s) will be repaired or replaced (At the Company’s option) without charge
for parts or labor.
To obtain repair or replacement within the terms of the warranty, the product is to be delivered with proof of warranty coverage ( e.g. dated bill of sale, receipt),
specification of defect, freight pre-paid with Returns Good Authorization Number from Smittybilt to place of purchase. Items returned to Smittybilt without a Returns
Authorization Number will be refused and returned to sender at the sender’s expense.
This warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through altercation, improper
installation, mishandling, misuse, neglect accident or acts of nature. THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE
PURCHASER FOR THIS PRODUCT.
This warranty is in lieu of all expressed warranties and liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHTH WITHIN A PERIOD OF 90 DAYS FROM DATE OF ORIGINAL PURCHASE.IN NO CASE SHALL
THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED,WHATSOEVER. No person or representative is authorized to assume for the company any liability other than expressed herein in connection with the sale of this
product. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage, therefore above
limitations may not apply to you. This warranty gives the purchaser specific legal rights. The purchaser may have additional rights, which vary from state to state.
To assure product quality, Smittybilt reserves the right to change product design, material, specification and finishes without prior notice to customers. This limited warranty
gives you specific legal rights and you may also have other rights, which may vary from state to state. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply as to you. Also, some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. Smittybilt reserves the right to discontinue product lines and substitute products, or provide other remedies than
those listed in this limited warranty for those discontinued products.
CARE AND MAINTENANCE
To protect your investment it is
recommended to regularly wash and wax
this part. Do not use any type of cleaners
that contain abrasives that may damage the
finish of your part.