AEM Infinity Supported Applications - Mazda 1986-2002 16B & 20B Rotary - Manual (Page 18)

18
© 2014 AEM Performance Electronics
or CDI that accepts a f alling edge f ire
signal.
14 Coil 1 1-H
Leading Coil
(wasted spark)
25 mA max source current
0-5V f alling edge f ire. Do NOT connect
directly to coil primary . Must use an ignitor
or CDI that accepts a f alling edge f ire
signal.
15 Coil 6 --- --- 25 mA max source current
0-5V f alling edge f ire. Do NOT connect
directly to coil primary . Must use an ignitor
or CDI that accepts a f alling edge f ire
signal.
16 Coil 5 1-J
Rear Trailing Coil
(sequential)
25 mA max source current
0-5V f alling edge f ire. Do NOT connect
directly to coil primary . Must use an ignitor
or CDI that accepts a f alling edge f ire
signal.
17 VR0 (+) - Crank 4-E
Crank Sensor
(NE)+
Dif f erential Variable
Reluctance Zero Cross
Detection
See Setup Wizard page Cam/Crank f or
options.
18 VR0 (-) - Crank 4-H Crank Sensor -
Dif f erential Variable
Reluctance Zero Cross
Detection
See Setup Wizard page Cam/Crank f or
options.
19 VR1 (-) - Cam 4-H Crank Sensor -
Dif f erential Variable
Reluctance Zero Cross
Detection
See Setup Wizard page Cam/Crank f or
options.
20 VR1 (+) - Cam 4-G
Crank Sensor
(G) +
Dif f erential Variable
Reluctance Zero Cross
Detection
See Setup Wizard page Cam/Crank f or
options.
21 LS 2 3-D
Radiator Fan
Control
Lowside switch, 4A max, No
internal f ly back diode.
See Setup Wizard Page "LowSide
Assignment Tables" f or output assignment
and 2D table "LS2_Duty [%]" f or on/of f
activ ation.
22 LS 3 1-F MIL
Lowside switch, 4A max with
internal f ly back diode.
Inductiv e load should NOT
hav e f ull time power.
See Setup Wizard page and corresponding
Tables f or Idle Air Control.
23 Sensor GND 4-D Sensor Ground 1 Dedicated analog ground Analog 0-5V sensor ground
24 Sensor GND --- --- Dedicated analog ground
Analog 0-5V sensor ground also f ound on
aux connector
25 Digital 0 - Crank --- ---
10K pullup to 12V. Will work
with ground or f loating
switches.
The S2000 uses a VR crank sensor.
26 Digital 1 - Cam1 --- ---
10K pullup to 12V. Will work
with ground or f loating
switches.
The S2000 uses VR cam sensors.
27 Digital 2 - Cam2 --- ---
10K pullup to 12V. Will work
with ground or f loating
switches.
The S2000 uses VR cam sensors.
28
Digital 3 – Flex
Fuel
--- ---
10K pullup to 12V. Will work
with ground or f loating
switches.
See Setup Wizard page Input Function
Assignments f or input mapping options.
29 Digital 4 - VSS#1 1-M
Vehicle Speed
Sensor
10K pullup to 12V. Will work
with ground or f loating
switches.
See Setup Wizard page Vehicle Speed f or
calibration constant.
30 Digital 5 --- ---
10K pullup to 12V. Will work
with ground or f loating
switches.
See Setup Wizard page f or A/C activ ation
31 Digital 6 --- ---
10K pullup to 12V. Will work
with ground or f loating
Found on the Aux Connector. Input can be
assigned to dif f erent pins. See Setup