Philips 10001541 - Manual (Page 19)

English
• 19 •
dispensed. Clean the suction pipe externally with a damp
cloth.
The cappuccinatore must be removed and
completely washed once a week.
• (Fig.19) - Press the button (18) again.
• Prime the circuit as described in section 4.5 to make the
machine ready for use.
Note: the machine is ready when the buttons (15
and 16) are permanently on.
Note: if it is not possible to dispense a
cappuccino as described, prime the circuit as
explained in Section 4.5, then repeat the procedure.
The same procedure can be used to heat other
beverages.
9 PANNARELLO
Pannarello can be used for dispensing hot water and
ejecting steam instead of the cappuccinatore.
Remove the cappuccinatore before installing the
Pannarello (Fig.29-30):
- Loosen the ring nut without taking it off.
- Remove the cappuccinatore coupling from the steam
spout.
Install the Pannarello (Fig.31):
- Insert the Pannarello completely into the steam spout.
- Tighten the ring nut securely.
(Fig.32 - Fig.33) - Prepare the machine by using the
Pannarello as described in Sections 7 and 8 to dispense
hot water or steam.
(Fig.34 - Fig.35) - After using the machine, when it has
cooled down, remove the lower part of the Pannarello
and wash it with lukewarm water.
(Fig.36) - Once a week, remove the upper part as well
and wash it with lukewarm water.
10 CLEANING
Maintenance and cleaning must be performed only
when the machine has cooled down and has been
disconnected from the power supply.
• Do not immerse the machine in water nor place any of its
parts in a dishwasher.
• Do not use spirit, solvents and/or aggressive chemical
agents.
• We recommend cleaning the water tank and fi lling it up
with fresh water daily.
• (Fig.20) - After heating milk, brew a small quantity of hot
water as well.
Danger! If the end part of the cappuccinatore has
been removed, do not eject steam.
• (Fig.22 - 23) - Clean the cappuccinatore weekly.
In order to do this, please:
- Remove the cappuccinatore end part.
- Separate the cappuccinatore upper and lower parts.
- Wash all the cappuccinatore parts with lukewarm
water.
- Wash the suction pipe with a damp cloth and remove
any milk residue.
- Assemble the cappuccinatore.
- Place the end part of the cappuccinatore in the coupling
on the machine (make sure it is completely inserted).
• (Fig.24) - Empty and clean the drip tray daily.
• Use a damp and soft cloth to clean the appliance.
• (Fig.17) - Perform the following operations to clean the
pressurized fi lter holder:
- (Fig.10) - Remove the fi lter, and wash it thoroughly with
hot water.
- Remove the pin, wash it thoroughly with hot water.
- Wash the internal part of the pressurized fi lter holder.
• Do not dry the machine and/or its components in a
microwave and/or in a conventional oven.
Note: do not wash the pressurized portafi lter in
the dishwasher.
11 DESCALING
The formation of limescale inside the appliance is
inevitable. It is necessary to descale the machine every
1-2 months of use and/or when you notice a reduction in
the water delivery.
Please use Saeco descaling solution in your
machine (Fig.B). It has been specifically
developed to preserve performance and functionality
throughout the lifetime of the machine and to ensure,
with regular use, a high quality delivered product.
Warning! Do not use vinegar as a descaling
solution.
• (Fig.1) - Remove and empty the water tank.
• (Fig.2) - Mix the descaling solution with water as specifi ed
on the descaling solution box and fi ll the water tank. Fit
the tank into the machine.
• (Fig.3) - Turn on the machine by pressing the ON/OFF
button (2).
• Wait for the buttons (15 - 16) to be permanently on.
• (Fig.29 - 30) - Remove the cappuccinatore.
- Loosen the ring nut without taking it off.
- Remove the cappuccinatore coupling from the steam
spout.