Barco R9002139 - Manual (Page 4)

Table of Contents
i-1 5975039 BARCOVISION 508 100698
i
TABLE OF CONTENTS
TABLE OF CONTENTS ..........................................I-1
SAFETY INSTRUCTIONS ...................................... 1-1
On safety ....................................................................................1-1
On installation ............................................................................. 1-2
On servicing ...............................................................................1-2
On cleaning .................................................................................1-2
On repacking ..............................................................................1-2
On illumination ............................................................................. 1-2
LOCATION AND FUNCTIONS OF
CONTROL .............................................................. 2-1
Rear Panel Terminology..............................................................2-1
Front Panel Terminology .............................................................2-1
Control panel terminology ...........................................................2-2
a. The local keypad ....................................................................2-2
b. RCU control panel terminology ...............................................2-2
CONNECTIONS ..................................................... 3-1
Switching on/off .........................................................................3-1
Signal input connection to the projector : ..................................3-1
Power (mains) cord connection ................................................ 3-1
Connecting a Composite Video source. ....................................3-2
Connecting a S-Video to port 2. .................................................3-2
Connecting a RGB Analog source with composite sync. ......... 3-3
Connecting a Component source. ............................................. 3-4
Connecting a RF signal to the projector (optional) .................... 3-4
Connecting an external audio signal (optional) ......................... 3-5
Peripheral equipment ..................................................................3-5
Connecting a RCVDS 05 switcher to the projector. .................. 3-5
Connecting a VS05 switcher to the projector. .......................... 3-5
Connecting an IR Remote Receiver to the projector................. 3-5
CONTROLLING ..................................................... 4-1
Battery installation in the RCU. ...................................................4-1
How to use the RCU ................................................................... 4-2
Projector address .......................................................................4-2
How to display a projector address? ........................................ 4-2
How to program an address into the RCU? .............................. 4-3
Input selection............................................................................. 4-3
Picture controls ..........................................................................4-4
The Pause key. ........................................................................... 4-4
Sound control with the RCU (optional) ...................................... 4-5
START UP OF THE ADJUSTMENT
MODE ..................................................................... 5-1
Adjustment mode ........................................................................ 5-1
RANDOM ACCESS ADJUSTMENT
MODE ..................................................................... 6-1
Starting up the random access adjustment mode. .................... 6-1
Overview 'random Access Adjustment' mode. ......................... 6-1
Selecting Setup Pattern ..............................................................6-2
Internal Cross Hatch Pattern ......................................................6-2
Random access adjustment mode selection menu. .................. 6-2
Picture Tuning ............................................................................. 6-2
Color Balance ............................................................................. 6-3
Gamma ........................................................................................6-3
Blue stretch ................................................................................ 6-3
Decoding ..................................................................................... 6-3
Color Select ................................................................................ 6-4
Geometry Adjustments ...............................................................6-4
Horizontal Phase Adjustment ..................................................... 6-5
Raster Shift Adjustment .............................................................6-5
Left-Right (east-west) Adjustments ..........................................6-7
Top-Bottom (north-south) Adjustments .....................................6-8
Horizontal Size Adjustment ........................................................6-9
Vertical Linearity Adjustment ..................................................... 6-9
Horizontal Size Adjustment ......................................................6-10
Blanking Adjustments ...............................................................6-10
Convergence Adjustment ........................................................6-12
SERVICE MODE .................................................... 7-1
Starting up the Service mode. ....................................................7-1
Overview flowchart 'Service' mode. .........................................7-1
Projector Set-up .........................................................................7-2
Identification ................................................................................7-2
Total Run Time ............................................................................7-3
Change password .....................................................................7-3
Change Projector Address ........................................................7-3
Change baudrate ........................................................................7-4
Power up mode ..........................................................................7-4
Memory management .................................................................7-4
Copy a block ...............................................................................7-5
Deletion of blocks .......................................................................7-5
Deleting block by block ...............................................................7-5
Deletion of all blocks ...................................................................7-6
All settings to midposition ...........................................................7-6
Undo all settings to midpos ........................................................7-6
R & B convergence mid ..............................................................7-7
Undo R & B convergence mid ....................................................7-7
Green convergence mid ............................................................7-7
Undo green convergence mid ....................................................7-7
Common Settings ........................................................................7-8
G2 Adjustment ............................................................................7-8
CRT run in cycle .........................................................................7-8
I2C Diagnostics ...........................................................................7-9
OPTIONS ............................................................... 8-1
IR Receiver 800 ..........................................................................8-1
Hardwired RCU. .........................................................................8-1
RCVDS 05 Source Selector .......................................................8-1
VS05 Switcher ...........................................................................8-1
Adapter and communication cables ..........................................8-1
Ceiling mount CM50 ....................................................................8-1
Tuner kit ......................................................................................8-2
APP. A : TUNER MODE ........................................ A-1
Tuner mode ................................................................................ A-1
How to activate the tuner mode ? ............................................ A-1
Tuner setup ............................................................................... A-2
Broadcasting System ................................................................ A-2
Auto search ............................................................................... A-3
Manual search ........................................................................... A-3
Organise channel list ................................................................. A-4
Bilingual ...................................................................................... A-4
Teletext ...................................................................................... A-5