Placing the speakers connecting the speakers, 03 connecting your equipment – Pioneer VSX-2021 User Manual

Page 13

Connecting your equipment

Other speaker connections

! Your favorite speaker connections can be

selected even if you have fewer than 5.2
speakers (except front left/right speakers).

! When not connecting a subwoofer, connect

speakers with low frequency reproduction
capabilities to the front channel. (The
subwoofer’s low frequency component
is played from the front speakers, so the
speakers could be damaged.)

! After connecting, be sure to conduct the

Full Auto MCACC (speaker environment
setting) procedure. See Automatically
conducting optimum sound tuning (Full Auto
MCACC) on page 26 .

Placing the speakers

Refer to the chart below for placement of the
speakers you intend to connect.

SW 2 SW 1

FHL

FWL

SBL

SBR

FWR

FHR

30 30

120

! Place the surround speakers at 120º from

the center. If you, (1) use the surround
back speaker, and, (2) don’t use the front
height speakers / front wide speakers, we
recommend placing the surround speaker
right beside you.

! If you intend to connect only one surround

back speaker, place it directly behind you.

! Place the left and right front height speakers

at least one meter directly above the left and
right front speakers.

THX speaker system setup

If you are using a THX certified subwoofer, use
the THX INPUT jack on the subwoofer (if your
subwoofer has one) or switch the filter position
to THX on your subwoofer.
See also THX Audio Setting on page 69 to make
the settings that will give you the best sound
experience when using the Home THX modes
(page 37).

Some tips for improving sound

quality

Where you put your speakers in the room has
a big effect on the quality of the sound. The
following guidelines should help you to get the
best sound from your system.
! The subwoofer can be placed on the floor.

Ideally, the other speakers should be at about
ear-level when you’re listening to them.
Putting the speakers on the floor (except the
subwoofer), or mounting them very high on a
wall is not recommended.

! For the best stereo effect, place the front

speakers 2 m to 3 m apart, at equal distance
from the TV.

! If you’re going to place speakers around your

CRT TV, use shielded speakers or place the
speakers at a sufficient distance from your
CRT TV.

! If you’re using a center speaker, place the

front speakers at a wider angle. If not, place
them at a narrower angle.

! Place the center speaker above or below the

TV so that the sound of the center channel is
localized at the TV screen. Also, make sure the
center speaker does not cross the line formed
by the leading edge of the front left and right
speakers.

! It is best to angle the speakers towards the

listening position. The angle depends on
the size of the room. Use less of an angle for
bigger rooms.

! Surround and surround back speakers should

be positioned 60 cm to 90 cm higher than your
ears and tilted slightly downward. Make sure
the speakers don’t face each other. For DVD-
Audio, the speakers should be more directly
behind the listener than for home theater
playback.

! Try not to place the surround speakers farther

away from the listening position than the front
and center speakers. Doing so can weaken the
surround sound effect.

Connecting the speakers

Each speaker connection on the receiver com-
prises a positive (+) and negative (–) terminal.
Make sure to match these up with the terminals
on the speakers themselves.

CAUTION

! These speaker terminals carry HAZARDOUS

LIVE voltage. To prevent the risk of electric
shock when connecting or disconnecting the
speaker cables, disconnect the power cord
before touching any uninsulated parts.

! Make sure that all the bare speaker wire is

twisted together and inserted fully into the
speaker terminal. If any of the bare speaker
wire touches the back panel it may cause the
power to cut off as a safety measure.

Bare wire connections

CAUTION

Make sure that all speakers are securely
installed. This not only improves sound quality,
but also reduces the risk of damage or injury
resulting from speakers being knocked over or
falling in the event of external shocks such as
earthquakes.

1 Twist exposed wire strands together.
2 Loosen terminal and insert exposed
wire.
3 Tighten terminal.

10 mm

This manual is related to the following products:

VSX-LX55