Using the sleep timer, Dimming the display, Switching the hdmi output – Pioneer SC-LX56-S User Manual
Page 73: Checking your system settings, Resetting the system
73
09
Using other functions
Using the sleep timer
The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use the remote control to set the sleep timer.
% Press
to the receiver operation mode, then press SLEEP repeatedly to set the sleep
time.
30 min
60 min
Off
90 min
! You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle
through the sleep options again.
! The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.
Dimming the display
You can choose between four brightness levels for the front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
% Press
to the receiver operation mode, then press DIMMER repeatedly to change the
brightness of the front panel display.
! You can also choose to turn the display off. In this case, the FL OFF indicator lights.
Switching the HDMI output
Set which terminal to use when outputting video and audio signals from the HDMI output terminals.
The HDMI OUT 1 terminal is compatible with the Control with HDMI function.
% Press
to the receiver operation mode, then press HDMI OUT.
Please wait a while when Please wait ... is displayed.
The output switches among HDMI OUT ALL, HDMI OUT 1 and HDMI OUT 2 each time the button is pressed.
! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro-
nized amp mode, switch to HDMI OUT 1, then select the synchronized amp mode on the TV using the TV’s
remote control.
Checking your system settings
Use the status display screen to check your current settings for features such as surround back channel process-
ing and your current MCACC preset.
1 Press
to the receiver operation mode, then press STATUS to check the system
settings.
The front panel display shows each of the following settings for three seconds each: Input Source
d Sampling
Frequency
d MCACC preset d ZONE 2 input d ZONE 3 input d HDMI OUT.
2 When you’re finished, press STATUS again to switch off the display.
Resetting the system
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.
Set MULTI-ZONE to MULTI ZONE OFF.
! Disconnect the iPod and USB memory device from the receiver beforehand.
! Set the Control with HDMI to OFF (see
HDMI Setup
on
page 63
).
1 Switch the receiver into standby.
2 While holding down ENTER on the front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘RESET’ using PRESET
k/l, then press ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.
! Note that all settings will be saved, even if the receiver is unplugged.
Default system settings
Setting
Default
Digital Video Converter
ON
SPEAKERS
FH/FW ON
Speaker System
9.1ch FH/FW
Speaker Setting
Front
SMALL
Center
SMALL
FH/FW
SMALL
Surr
SMALL
SB
SMALLx2
SW
YES
Surround Position
IN REAR
Crossover
80 Hz
X-Curve
OFF
DIMMER
Medium bright
Inputs
See
Input function default and possible settings
on
page 42
HDMI
HDMI Audio
AMP
HDMI output
HDMI OUT ALL
Control
OFF
Control Mode
--- (OFF)
ARC (Audio Return Channel)
--- (OFF)
PQLS
--- (AUTO)
Standby Through
OFF
DSP
Power On Level
LAST
Volume Limit
OFF
Mute Level
FULL