RADWAG PUE C/31H/Z Indicator User Manual

User manual, For indicators pue c/31 series

Text mode
Original mode

User Manual

for indicators PUE C/31 series

Manual number:
ITKU-17-01-03-10-A

FOR COOPERATION WITH TENSOMETERS

M A N U F A C T U R E R O F E L E C T R O N I C

W E I G H I N G I N S T R U M E N T S

RADWAG Wagi Elektroniczne 26 – 600 Radom Bracka 28 Street - POLAND
Phone +48 48 38 48 800, phone/fax. +48 48 385 00 10
Selling department +48 48 366 80 06
www.radwag.com

This manual is related to the following products:

PUE C/31H Indicator PUE C/31 Indicator

Table of contents

Document Outline

1. INTENDED USE
2. PRECAUTIONS
- 2.1. Maintenance
- 2.2. Accumulator / battery pack
  - 2.2.1. Power supply of weighing indicators in plastic casings
  - 2.2.2. Replacement of worn batteries
- 2.3. Operation in a strong electrostatic field
3. WARRANTY CONDITIONS
4. MAIN DIMENSIONS
5. GETTING STARTED
6. KEYPAD
7. KEYS’ FUNCTIONS
8. INSCRIPTIONS ON THE DISPLAY
9. USER MENU
- 9.1. Submenus
- 9.2. Browsing user menu
  - 9.2.1. Keypad
  - 9.2.2. Return to the weighing mode
10. WEIGHING
- 10.1. Tarring
- 10.2. Inscribing tare value
- 10.3. Zeroing
- 10.4. Weighings in two ranges
- 10.5. Selection of basic weight unit
- 10.6. Temporarily selected unit
11. MAIN PARAMETERS
- 11.1. Setting a filtering level
- 11.2. Median filter
- 11.3. Autozero function
- 11.4. Tare function
12. RS 232 PARAMETERS
- 12.1. Printout type
- 12.2. Minimal mass threshold
- 12.3. Baud rate
- 12.4. Serial transmission parameters
13. OTHER PARAMETERS
- 13.1. Backlight function
  - 13.1.1. Backlight for supplying from mains
  - 13.1.2. Backlight for supplying from batteries
- 13.2. “Beep” signal – after pressing a key
- 13.3. Automatic switch-off
- 13.4. Battery voltage level check
14. WORK MODES
- 14.1. Setting accessibility of operation modes
- 14.2. Selecting quantity of operation modes
- 14.3. Counting pieces of the same mass
- 14.4. +/- control referring to the inscribed standard mass
- 14.5. Control of % deviation referring to the inscribed standard mass
  - 14.5.1. Standard mass determined by its weighing
  - 14.5.2. Mass of standard inscribed to scale memory
- 14.6. Automatic tare
- 14.7. Measurement max force on the pan – latch
- 14.8. Totalizing
- 14.9. Weighing animals
- 14.10. Tare memory
  - 14.10.1. Entering the tare value to the scale memory
  - 14.10.2. Selecting a tare value from the memory
15. USER CALIBRATION
- 15.1. Calibration
- 15.2. Start mass adjustment
16. COOPERATION WITH PRINTER
17. COOPERATION WITH COMPUTER
18. COMMUNICATION PROTOCOL
- 18.1. General information
- 18.2. A set of commands for RS interfaces
- 18.3. Respond message format
- 18.4. Command’s description
- 18.5. Manual printouts / automatic printouts
- 18.6. Continuous transmission
- 18.7. Configuring printouts
19. ERROR COMMANDS
20. TROUBLE SHOOTING
21. TECHNICAL PARAMETERS
- 21.1. Metrological parameters
- 21.2. Ambient conditions
- 21.3. Power supply
22. ADDITIONAL EQUIPMENT