RADWAG WTB 2000 Precision Balance User Manual

User manual, Precisions scales – wtb series

Text mode
Original mode

User Manual

Precisions scales – WTB series

Manual number:
ITKU-24-01-03-10-A

M A N U F A C T U R E R O F E L E C T R O N I C
W E I G H I N G I N S T R U M E N T S

RADWAG Wagi Elektroniczne 26 – 600 Radom Bracka 28 Street - POLAND
Phone +48 48 384 88 00, phone/fax. +48 48 385 00 10
Selling department +48 48 366 80 06
www.radwag.com

This manual is related to the following products:

WTB 200 Precision Balance

Table of contents

Document Outline

1. INTENDET USE
2. PRECAUTIONS
- 2.1. Maintenance
- 2.2. Accumulator / battery pack
3. WARRANTY CONDITIONS
4. MAIN DIMENSIONS
5. UNPACKING AND ASSEMBLY
6. GETTING STARTED
7. BALANCE LEVELLING
8. KEYPAD
9. KEYS’ FUNCTIONS
10. INSCRIPTIONS ON THE DISPLAY
11. USER MENU
- 11.1. Submenus
- 11.2. Browsing user menu
  - 11.2.1. Keypad
  - 11.2.2. Return to the weighing mode
12. WEIGHING
- 12.1. Tarring
- 12.2. Inscribing tare value
- 12.3. Zeroing
- 12.4. Weighings in two ranges
- 12.5. Selection of basic weight unit
- 12.6. Temporarily selected unit
13. MAIN PARAMETERS
- 13.1. Setting a filtering level
- 13.2. Median filter
- 13.3. Autozero function
- 13.4. Tare function
14. RS 232 PARAMETERS
- 14.1. Printout type
- 14.2. Minimal mass threshold
- 14.3. Baud rate
- 14.4. Serial transmission parameters
15. OTHER PARAMETERS
- 15.1. Backlight function
  - 15.1.1. Backlight for supplying from mains
  - 15.1.2. Backlight for supplying from batteries
- 15.2. “Beep” signal – after pressing a key
- 15.3. Automatic switch-off
- 15.4. Battery voltage level check
16. OPERATION MODES
- 16.1. Setting accessibility of operation modes
- 16.2. Selecting quantity of operation modes
- 16.3. Counting pieces of the same mass
- 16.4. +/- control referring to the inscribed standard mass
- 16.5. Control of % deviation referring to the inscribed standard mass
  - 16.5.1. Standard mass determined by its weighing
  - 16.5.2. Mass of standard inscribed to scale memory
- 16.6. Automatic tare
- 16.7. Measurement max force on the pan – latch
- 16.8. Totalizing
- 16.9. Weighing animals
- 16.10. Tare memory
  - 16.10.1. Entering the tare value to the scale memory
  - 16.10.2. Selecting a tare value from the memory
17. USER CALIBRATION
- 17.1. Calibration
- 17.2. Start mass adjustment
18. COOPERATION WITH PRINTER
19. COOPERATION WITH COMPUTER
20. COMMUNICATION PROTOCOL
- 20.1. General information
- 20.2. A set of commands for RS interfaces
- 20.3. Respond message format
- 20.4. Command’s description
- 20.5. Manual printouts / automatic printouts
- 20.6. Continuous transmission
- 20.7. Configuring printouts
21. ERROR COMMANDS
22. TROUBLE SHOOTING
23. TECHNICAL PARAMETERS
24. ADDITIONAL EQUIPMENT