Young Wind Tracker Model 06201 - Manual (Page 3)

Page 2 06201-90(I)
MOUNTING AND START-UP
1. For best visibility, place the Wind Tracker in a location free of
direct sunlight. Mount it using the attached bracket or remove
bracket for flush mounting to a bulkhead or panel cutout. Panel
cutout dimensions are given in the specifications. An optional
rack mounting panel (Model 06280) and protective enclosure
(Model 06260) are available from your YOUNG supplier.
2. Connect cables to terminals according to wiring diagram.
IMPORTANT NOTE! Please observe correct position of
back-panel Input Selector Switch according to wiring
diagram.
3. Connect GND terminal to suitable earth ground.
4. Insert power supply plug into power jack, plug power supply
into a suitable AC wall outlet or connect to suitable 12 to 30
VDC power source to terminals.
IMPORTANT NOTE! Do not connect more than one power
source to the Wind Tracker at the same time.
5. When power is applied, the Wind Tracker will display firmware
version number then begin to display wind information as
follows:
• Wind speed
• Wind speed units
• Maximum wind speed or direction degrees
• Wind direction (single orange indicator)
• Direction variability (green indicators)
• Alarm status indicators (if selected)
• Wind speed & direction averaging indicator (if selected)
6. Observe display to confirm proper operation.
CHANGING SETTINGS
Wind Tracker parameters may be inspected or changed in SETUP
mode which is enabled by simultaneously pressing both ENTER
and SELECT keys for about 4 seconds. When SETUP mode is
active, abbreviations identify each function and available options
as listed below. The SELECT key changes options or values. The
ENTER key saves and moves to the next parameter.
Appearance of options depends on parameter settings. Some
options may be hidden.
DISPLAY SETUP FUNCTION
Input / Sensor Type
InP 03 Wind Sentry
04 Wind Monitor-Jr
05 Wind Monitor
05A Wind Monitor-AQ
09 Wind Monitor-SE or YOUNG sonic anemometer
SEr Serial input when used as remote display
Ld2 Line Driver 4-20mA input (0-100 m/s)
Hd Wind Monitor HD
Ldi Line Driver 4-20mA input (0-50 m/s)
Wind Speed Units (annunciator blinks)
SPd unt SELECT key changes units. ENTER to save
Display Averaging (annunciator blinks)
dSP no Instantaneous data displayed
YES Average data displayed
PEr 030 Set averaging period in seconds (0-999).
Display will update at this interval.
Right Display Window Selection
dSP SPd Maximum wind speed
dir Wind Direction degrees
Wind Direction Alarm (annunciator blinks)
ALr no Direction alarm not armed
YES Direction alarm armed
ALr dir SELECT key sets direction alarm sector start.
ENTER key saves.
ALr SPn SELECT key sets direction alarm sector span.
ENTER key saves.
Wind Speed Alarm (annunciator blinks)
ALr no Speed alarm not armed
YES Speed alarm armed
ALr 000 Alarm set-point. SELECT key increments value.
ENTER key saves.
Alarm Delay Time
dLY 030 Alarm delay time in seconds (0-999). SELECT key
increments value. ENTER key saves.
Sound
Snd no No sound
YES Audible beep with alarm activations or average
update.
Wind Direction Voltage Output Scale
dir 360 0-360 degrees
540 0-540 degrees
Serial Output Type
Out bin Binary output for remote Wind Tracker displays
ASC ASCII text wind speed & direction
Test Functions
tSt no No test
YES Test
tSt ALr SELECT key closes alarm relays.
CAL 0.00 SELECT key alternates between 0.00 and
5.00 VDC output to calibrate external devices.
tSt dsP SELECT key tests display sections.
OPERATION
ALARMS
Wind speed and direction alarms each have their own set-point,
LED status indicator, and relay contacts. The Alarm Delay parameter
establishes time duration in or out of the set-point range needed
for the alarm to change state. Front panel LEDs indicate alarm
status during operation.
LED Off = Alarm not armed and OFF. Relay open
LED Steady = Alarm armed and OFF. Relay open
LED Blinking = Alarm armed and ON. Relay closed.
Audible beep if Sound parameter is enabled.