beautypg.com

ConTech Lighting RDA4L User Manual

Wiring diagram 1 wiring diagram 2

background image

Flexible Conduit

Trim Frame

J-Box

Housing

RL-KIT #3

Key Hole

Slots

Mounting Stud

Flat Hanger Bar

Narrow Slots

www.contechlighting.com

1-847-559-5500

RDA4L INST

All specifications subject to change without notice.

IMPORTANT SAFETY INSTRUCTIONS:

• Read all the instructions before installation. Save instructions for later use.

• Turn off power at fuse or circuit breaker box before installation or before doing any maintenance work.

• Product must be grounded to avoid potential electric shock and any other potential hazards. Work on a sturdy, nonconductive ladder.

• Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with National

Electrical Code and local codes. Use of accessory equipment is not recommended. For indoor use only.

• Installing contrary to instructions may cause unsafe conditions.

• Do not block light from the trim aperture, in whole or in part, as this may cause unsafe conditions. Do not install closer than 6" from any

curtain or similar combustible material.

Warning: Risk of fire. Most dwellings built before 1985 have supply wire rated at 60°C. Consult a qualified electrician before installation.

• To avoid hazards to children, account for all parts and properly dispose of all packing materials.

• Call the Technical Support department at Con-Tech Lighting with any installation questions: 847.559.5500.

INSTALLATION PROCEDURES: NEW CONSTRUCTION UNITS

1. Carefully remove packing inserts and slim inner carton containing the

trim frame.

2. Locate the Hex Key (tightens hex head screws that secure housing to

mounting frame, and head tilt locking screw (Fig. 1).

3. Assemble RL-KIT #3:

• Select “L” bracket with the longer base plate. Attach to short end of

mounting frame with J-Box by fitting keyhole slots in bracket over the

setscrews in mounting plate. Adjust to desired length, tighten screws.

Repeat with remaining bracket on opposite end of mounting frame.

• Mount the wing-style brackets to the “L” brackets with the open end

facing out (Fig. 2). Pass mounting stud through bracket slot,

secure with wing nut and washer provided.

• Narrow slots in the bracket accept flat hanger bars (ConTech

HB-24), C-shaped openings accept C-Channel hanger bars (ConTech

HBC-24). C-shaped openings may also be used for 1/2" conduit.

• Vertical slots in brackets allow a 3" overall height adjustment.

Desired housing position is for the mounting frame lip to be even

with the finished ceiling, firmly tighten the wing nut.

4. Use Hex Key to make final height adjustments of the housing within

the mounting frame (3/4” maximum height adjustment). DO NOT

PLACE ANY INSULATION MATERIAL WITHIN THREE INCHES OF

THE HOUSING.

5. The RDA4L housing is pre-wired. Power must only be brought to the

junction box on the housing. Maximum of 8 No. 12 AWG through

branch circuit conductor suitable for 75°C permitted in box.

WARNING: Power source must conform to requirements of the fixture

(see labels on fixture), all NEC and local electrical codes.

Before starting wire connections, disconnect power at

circuit breaker or fuse, turning power off at switch leg is not

sufficient to prevent electrical shock. Make junction box

connections per appropriate wiring diagram, based upon

dimming option being installed (Fig. 3) Close junction box

cover after wiring (ensure that all wires are within box

before closing).

TRIM INSTALLATION

• Trimmed option: Squeeze torsion springs on trim and insert them into

brackets located inside of housing. Push trim upward until it seats

firmly against the ceiling.

• Trim-less option: housing mounting frame and trimless frame each

contain eight (8) matching fastening points for secure retention in

ceiling. Using #6 drywall screws (supplied by others) fasten the

trimless frame to the drywall and housing mounting frame. Once

secured, joint compound can be applied.

Continued on page 2

Head Tilt Locking Screw

C-Channel

Hanger Bar Slots

Mounting

Frame

Hex Head

Screws (4)

For ConTech Lighting New Construction/Remodel Series Concealed Adjustable Illumination Series: RDA4L

WHITE

JUN

CT

IO

N

B

O

X

12/12D1/27/27D1/12D5/

27D5 OPTIONS

ELECTRICAL/DIMMING

NEUTRAL

BLACK

LINE

GREEN

GROUND

WHITE

JUN

CT

IO

N

B

O

X

12D2/27D2 OPTIONs

ELECTRICAL/DIMMING

NEUTRAL

BLACK

LINE

GREEN

GROUND

PURPLE

0-10V CONTROL

GRAY

WIRING DIAGRAM 1

WIRING DIAGRAM 2

Table of contents