Vaddio DomeVIEW Indoor Pendant Mount - Manual (Page 3)

Vaddio DomeVIEW Indoor Pendant Mount Dome Installation and User Guide - Document 341-444 Rev. C
Page 3 of 12
Indoor Pendant Mount Dome Enclosures Only (Cameras Not Included)
The Indoor Pendant Mount Dome Enclosures are for use with existing or standard Sony EVI-D70 and Canon
VC-C50iR cameras. The Dome enclosures can also be used with the Vaddio Standard EZCamera Cable
system for the EVI-D70 or the VC-C50i analog PTZ cameras. The dome enclosures without cameras are
listed below:
998-9100-050 Indoor Pendant Mount Dome Enclosure includes:
QTY Description
- Indoor Pendant Mount Dome Enclosure
1 Indoor Pendant Housing Assembly (Metal can with white ABS shroud and 1-1/2” NPT fitting)
1 White twist and lock trim ring
1 Clear dome bubble mounted to trim ring
1 1-1/2” NPT Locknut
- Camera bracket for Canon VC-C50iR PTZ camera (Camera Not Included)
3 4.5” x .375 (114.3mm x 9.525mm) Hex shaped stand-offs
1 6” x 6” (15.24cm x 15.24cm) Camera mounting stage
3 8-32 x .5” Flat head screws (flush mount)
2 8-32 x .5” pan head screws
2 Lock washers for pan head screws
998-9100-070 Indoor Pendant Mount Dome Enclosure includes:
QTY Description
- Indoor Pendant Mount Dome Enclosure
1 Indoor Pendant Housing Assembly (Metal can with white ABS shroud and 1-1/2” NPT fitting)
1 White twist and lock trim ring
1 Clear dome bubble mounted to trim ring
1 1-1/2” NPT Locknut
- Camera bracket for Sony EVI-D70 PTZ camera (Camera Not Included)
3 2.75” x .375 (69.85mm x 9.525mm) Hex shaped stand-offs
1 6” x 6” (15.24cm x 15.24cm) Camera mounting stage
3 8-32 x .5” Flat head screws (flush mount)
1 6” x 6” (15.24cm x 15.24cm) Camera mounting plate (attaches to camera)
1 ¼”-20 x ½” Mounting screw (to attach camera to mounting plate)
4 8-32 x .5” pan head screws
4 #8 Lock washers for pan head screws
INSTALLATION INSTRUCTIONS
DomeVIEW System Packages with Dome, Camera and Internal Mounting Bracket
999-9100-050 DomeVIEW 50iR Indoor Pendant Mount Dome System
999-9100-070 DomeVIEW 70 Indoor Pendant Mount Dome System
Indoor Pendant Mount Dome Enclosures
998-9100-050 for the Canon VC-C50iR PTZ Camera
998-9100-070 for the Sony EVI-D70 PTZ Camera
Before Starting the Installation
For cabling requirements, see the Cabling Requirements section. All installation work must conform to local
building codes and should be performed by qualified personnel.
Step-by-Step Assembly Instructions:
1) Unpack and verify the contents of the packaging against the lists on pages 2 and 3 of this manual.
Carefully remove all parts from the packaging and keep them together.
2) Remove the dome and trim ring assembly from the housing by rotating it counter clockwise until free.
Use caution when handing the dome to avoid scratching or scuffing the dome bubble.
3) Thread on the three hex shaped stand-offs (7) on to the studs in the bottom of the metal back can (8)
(See Figures 2 and 3).
4) Attach the camera mounting stage (6) to the stand offs (7) with three 8-32 x .5” flat head screws (5).