Balboa Water Group EL/VS 120V-240V - Manual (Page 22)

22
ML900 Panel Operation
Diagnostic Messages section for the ML900 is unique. Refer to the User Guide for additional information.
User Guide for panel ML900 is 40568-99.
Initial Start-up
When your spa is first actuated, it will go into Priming mode
(after displaying some configuration information). Please
see “Spa Behavior -- Start-up Information” for additional
information.
The Priming mode will last for up to 4 minutes and then the
spa will begin to heat and maintain the water temperature
in the Standard mode. You can exit Priming mode early by
pressing “Warm” or “Cool.”
Mode/Prog
This button is used to switch between standard, economy,
and sleep modes. Press “Mode/Prog” to enter mode
programming, press “Cool” to cycle through to desired mode
(LCD flashes until confirmed), then press “Mode/Prog” to
confirm selection
Standard mode maintains the desired temperature. Note
that the last measured spa temperature displayed is current
only when the pump has been running for at least 1 minute.
The “
” icon will display until the mode is changed.
Economy mode heats the spa to set temperature only during
filter cycles. The “
” icon will display until mode is
changed. Pressing “Jets 1” while in Economy mode puts the
spa in Standard-In-Economy mode, which operates the
same as Standard Mode, then reverts to Economy Mode
automatically after 1 hour. Both the “
” and
“ ” icons display in this mode. During this time,
a press of the “Mode/Prog” button will revert to Economy
Mode immediately.
Sleep mode heats the spa to within 20°F (11°C) of the set
temperature only during filter cycles. The “
” icon
will display until mode is changed.
Standby Mode
Pressing “Warm” or “Cool” then “Jets 2” will turn off all
spa functions temporarily. This is helpful when changing
a filter. Pressing any button resets the spa. On some
systems the “Jets 1” button will control the pump in
Standby Mode (“Drain Mode”). In this case, press any
other button to exit.
Locking the Panel
Press “Time” “Jets 1” then “Warm” within 3 seconds. When
locked, the PL “
PL ” light will light. All buttons are frozen
except the “Time” button. To unlock the panel, press “Time”
“Jets 1” then “Cool.”
Locking the Set Temperature
Press “Warm” or “Cool” then “Time,” “Jets 1,” and “Warm”
within 3 seconds to activate the lock. The TL “
TL ” light
will light when the set temperature is locked.
To unlock the set temperature, press “Warm” or “Cool” then
“Time,” “Jets 1” and “Cool.”
Time
When time hasn’t been programmed, the “ ” icon
flashes. (Time settings on EL1000 and some EL2000 systems
are not preserved in the event of power loss; time will have
to be reprogrammed upon each power up.)
Jets 3 Option Jets 1 Option
Invert Blower Fiber
Jets 3 Option Time Warm Jets 1 Jets 2 Jets 3 Option
Cool Mode/Prog Invert Blower Fiber Light
F2
TL
F1
PL
Setting the Time
Once the spa has been properly connected the first time (every power
up on the EL1000 and some EL2000 systems), notice the “
” icon
appearing on the screen.
Press then
Select the hour by pressing
Press
to exit the time setting procedure and enter the
optional filter cycle programming. (Exits programming
on some EL1000 and some EL2000 systems.)
Time Time
Press
to exit programming.
Press to enter.
Select minutes by pressing
Mode/Prog Mode/Prog
Time Time
Mode/Prog Mode/Prog
Mode/Prog Mode/Prog
Or
(Each press changes
the time by 1 minute) Warm Warm
Cool Cool
Or
(Each press changes
the time by 1 minute) Warm Warm
Cool Cool