AFX CNP240041LSNPWH - Manual

CENTRE LED PENDANTS
Models: CNP2400 Series
1 of 2
Safety Precautions
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
property damage.
It is recommended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
ASSEMBLY INSTRUCTIONS
1. Preparing for installation
A. Disconnect electrical power
fixture.
B. Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
2. Wiring-all wiring must take place inside junction box.
Caution: Make sure power is off at fuse or circuit breaker box.
Check power wires for damage or scrapes. If
wires are within three inches of
suitable for at least 90C (194F).
Note: Most dwellings built before 1985 have supply wire rated to
60C. Consult a qualified electr
A. Loosen four screws (3) and r
fixture along the slot.
B. Pre-Install gem bar plate
with two screws (2) (supplied)
C. Mark two mounting holes locations on the ceiling
bar plate as a template. Remove the gem bar plate and drill two
holes for the anchors (13)
D. Re-install the gem bar plate (1) by securing it with two
(2) on the junction box and two screws
C. Make all wires connections
wire nuts (supplied).
D. Connect the green wire
the green screw in the gem bar
E. The black wire from the fixture is connected to the black
from power source.
F. The white wire from the fixture is connected to the white
(neutral) wire from power source.
G. Tuck all connections neatly into junction box.
CENTRE LED PENDANTS
CNP2400 Series
Safety Precautions
Read all safety precautions and installation instructions carefully before
this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
commended that a qualified electrician perform all wiring. This
fixture must be wired in accordance with all national and local
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
INSTRUCTIONS
Preparing for installation
Disconnect electrical power at fuse or circuit breaker box before installing or servicing any part of this
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit breaker box.
power wires for damage or scrapes. If the power supply
wires are within three inches of the ballast power supply, use wire
90C (194F).
Most dwellings built before 1985 have supply wire rated to
60C. Consult a qualified electrician before installing.
screws (3) and remove gem bar (1) by shifting th
plate (1) on the junction box by securing it
(supplied).
Mark two mounting holes locations on the ceiling by using gem
bar plate as a template. Remove the gem bar plate and drill two
) (supplied). Install the anchors.
install the gem bar plate (1) by securing it with two
(2) on the junction box and two screws (14) on the ceiling.
connections to the appropriate wire. Secure
Connect the green wires from the fixture and power source to
in the gem bar.
The black wire from the fixture is connected to the black
The white wire from the fixture is connected to the white
(neutral) wire from power source.
Tuck all connections neatly into junction box.
LED Pendant Fixtures
120VAC / 60Hz
This fixture is designed for use in a 110-
Do not use on a dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
grounding, there must be a separate ground wire (green)
between this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
locations.
at fuse or circuit breaker box before installing or servicing any part of this
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit breaker box.
power supply
, use wire
Most dwellings built before 1985 have supply wire rated to
shifting the
on box by securing it
by using gem
bar plate as a template. Remove the gem bar plate and drill two
install the gem bar plate (1) by securing it with two screws
appropriate wire. Secure with
from the fixture and power source to
The black wire from the fixture is connected to the black wire
The white wire from the fixture is connected to the white
LED Pendant Fixtures
8060744 R0
-120VAC, 60Hz fused circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green) contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general indoor lighting in wet
at fuse or circuit breaker box before installing or servicing any part of this
as shown in figure
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.