AFX OCFW70050LBK - Manual

Outdoor Ceiling Fixture
Model: 326928 & OCFW70050LBK
1 of 1
Limited Factory Warranty
AFX Lighting, Inc. warrants this fixture is free from defects in materials and workmanship when installed and used under
period of 3 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or
not cover failure due to improper installation, misuse, mishandl
Safety Precautions
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
property damage.
It is recommended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
ASSEMBLY INSTRUCTIONS
1. Preparing for installation
A. Disconnect electrical power at fuse or circuit breaker box before installing or servicing any part of this fixture.
B. Carefully remove the fixture from the carton, and check that all parts a
of the screws or parts which are needed for installing the fixture.
A. Assemble 5 glass panels with
B. Place diffuser (2) on the frame bottom;
C. Place four diffusers (3) on frame sides.
secure the glass panels.
2. Wiring-all wiring must take place inside junction box.
Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for damage
or scrapes. If power supply wires are within three inches of
suitable for at least 90C (194F). Note:
to 60C. Consult a qualified electrician before installing.
D. Secure gem bar (4) on the junction bo
F. Make all wire connections to appropriate wire. Secure
G. Connect the green wires from the fixture and power source to the green screw on the gem bar
(4).
H. The black wire from the fixture is connected to the black wire from power source.
I. The white wire from the fixture is connected to the white (neutral) wire from power source.
G. Tuck all connections neatly into junction box.
3. Mounting
A. Thread nut (7) on stem (6). Adj
is exposed. Secure the necessary length with nut (7).
B. Install two longer screws (13) (supplied) on the backpanel and secure
(9) (supplied).
B. Install back panel (8) over stem (
4. Place the frame (11) over two (13
5. Restore power at fuse or circuit breaker box.
Outdoor Ceiling Fixture
& OCFW70050LBK
warrants this fixture is free from defects in materials and workmanship when installed and used under
years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or
not cover failure due to improper installation, misuse, mishandling or damage incurred in transit
Safety Precautions
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
commended that a qualified electrician perform all wiring. This
fixture must be wired in accordance with all national and local
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
ASSEMBLY INSTRUCTIONS
Preparing for installation
at fuse or circuit breaker box before installing or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not to misplace any
of the screws or parts which are needed for installing the fixture.
with metal frame (1):
Place diffuser (2) on the frame bottom;
frame sides. Fold four metal tabs to
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit breaker box. Check power wires for damage
are within three inches of the ballast power supply
Note: Most dwellings built before 1985 have supply wire rated
to 60C. Consult a qualified electrician before installing.
junction box (not supplied) with two screws (5) (suppli
to appropriate wire. Secure with wire nuts (supplied
from the fixture and power source to the green screw on the gem bar
the fixture is connected to the black wire from power source.
The white wire from the fixture is connected to the white (neutral) wire from power source.
Tuck all connections neatly into junction box.
). Adjust the length of the stem in the gem bar so that approx. 3/8”
Secure the necessary length with nut (7).
B. Install two longer screws (13) (supplied) on the backpanel and secure those
over stem (6) and secure it with the thumbnut (10).
13) backpan screws and secure it with two acorn nuts (1
. Restore power at fuse or circuit breaker box.
LED Flushmount
warrants this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a
years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or
ing or damage incurred in transit
This fixture is designed for use in a 110-
Do not use on a dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
grounding, there must be a separate ground wire (green)
between this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
damp locations only.
at fuse or circuit breaker box before installing or servicing any part of this fixture.
re included, as shown in figure below. Be careful not to misplace any
Make sure power is off at fuse or circuit breaker box. Check power wires for damage
power supply, use wire
Most dwellings built before 1985 have supply wire rated
(supplied)
(supplied).
from the fixture and power source to the green screw on the gem bar
the fixture is connected to the black wire from power source.
The white wire from the fixture is connected to the white (neutral) wire from power source.
in the gem bar so that approx. 3/8”
those with the two nuts
with two acorn nuts (12).
LED Flushmount
120VAC / 60Hz
8060664 R4
normal operating conditions for a
years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does
-120VAC, 60Hz fused circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green) contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general outdoor lighting in dry or
re included, as shown in figure below. Be careful not to misplace any