AFX CNP140027LSNPWH - Manual

CENTRE LED PENDANTS
Models: CNP1400 Series
1 of 2
Safety Precautions
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
property damage.
It is recommended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
ASSEMBLY INSTRUCTIONS
1. Preparing for installation
A. Disconnect electrical power
fixture.
B. Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
2. Wiring-all wiring must take place inside
junction box.
Caution: Make sure power is off at fuse or circuit
breaker box. Check power wires for damage or
scrapes. If the power supply wires are within three
inches of the ballast power supply
for at least 90C (194F).
Note: Most dwellings built before 1985 have supply
wire rated to 60C. Consult a qualified ele
before installing.
A. Loosen screws (3) pre
and remove gem bar by turning
clockwise.
B. Install gem bar on the juncti
with two screws (2) (supplied)
C. Make all wires connections
Secure with wire nuts (supplied
D. Connect the green wire
power source to the green screw
E. The black wire from the fixture is connected to the
black wire from power source.
F. The white wire from the fixture is connected to the
white (neutral) wire from power source.
G. Tuck all connections neatly into junction box.
CENTRE LED PENDANTS
CNP1400 Series
Safety Precautions
Read all safety precautions and installation instructions carefully before
this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
commended that a qualified electrician perform all wiring. This
fixture must be wired in accordance with all national and local
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
INSTRUCTIONS
Preparing for installation
Disconnect electrical power at fuse or circuit breaker box before installing or servicing any part of this
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
all wiring must take place inside
Make sure power is off at fuse or circuit
eck power wires for damage or
power supply wires are within three
power supply, use wire suitable
Most dwellings built before 1985 have supply
wire rated to 60C. Consult a qualified electrician
pre-installed on the gem bar (1)
by turning it counter
Install gem bar on the junction box by securing it
(supplied).
connections to the appropriate wire.
(supplied).
Connect the green wires from the fixture and
power source to the green screw in the gem bar.
The black wire from the fixture is connected to the
black wire from power source.
the fixture is connected to the
white (neutral) wire from power source.
Tuck all connections neatly into junction box.
LED Pendant Fixtures
120VAC / 60Hz
This fixture is designed for use in a 110-
Do not use on a dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
grounding, there must be a separate ground wire (green)
between this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
locations.
at fuse or circuit breaker box before installing or servicing any part of this
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
LED Pendant Fixtures
8060743 R0
-120VAC, 60Hz fused circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green) contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general indoor lighting in damp
at fuse or circuit breaker box before installing or servicing any part of this
as shown in figure
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.