Listings and approvals, Product line information – Notifier ACPS-610 User Manual

Page 2

Page 2 of 2 — DN-60244:C3 • 4/23/2012

Notifier®, FlashScan®, System Sensor®, and SpectrAlert® are registered

trademarks of Honeywell International Inc. Windows® is a registered

trademark of Microsoft.

of this document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.

We cannot cover all specific applications or anticipate all requirements.

All specifications are subject to change without notice.

For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.

www.notifier.com

Made in the U.S. A.

Listings and Approvals

These listings and approvals apply to the modules specified in

this document. In some cases, certain modules or applications

may not be listed by certain approval agencies, or listing may

be in process. Consult factory for latest listing status.
•

UL Listed: S635.

•

ULC Listed: S635.

• FM Approved.
•

CSFM: 7315-0028:0248, 7165-0028:0224, 7165-

0028:0243.

• MEA #30-08-E.
•

FDNY: COA #6085, #6098.

When used with the MARINE-EQ, appropriate seismic

bracket, and marine approved devices, the ACPS-610(E) is

approved by the following agencies:
• US Coast Guard: 161.002/50/0 (Standard 46 CFR).
• Lloyd's Register: 11/600013 (ENV 3 category).
• American Bureau of Shipping (ABS).

Product Line Information

ACPS-610: Addressable charger power supply, with selectable

built-in synchronization, and four built-in control modules. Sev-

eral mounting options available (see below).
ACPS-610E: Same as ACPS-610, but configured for 220/240

VAC operation.
CAB-PS1: The CAB-PS1 can house one ACPS-610(E) and

two 12 AH batteries. Dimensions: 15.218" (38.654 cm) high x

14.5" (36.83 cm) wide x 3.562" (9.048 cm) deep with door.
SEISKIT-PS/2/4: Seismic kit for mounting ACPS-610 in a

CAB-PS1. Includes bracket for two 12 AH batteries.
DR-PS1: When installing an ACPS-610(E) into an older ver-

sion of the CAB-PS1 used for an ACPS-2406(E), the new

wider door must be ordered for use with the older version

cabinet.
BB-25: The BB-25 can house one ACPS-610(E) and two 12

volt, 26 AH batteries.
BB-100: The BB-100 can house one ACPS-610(E) and two 12

volt, 55 AH or 100 AH AH batteries.
BB-200: The BB-200 can house one ACPS-610(E) and four

12 volt, 100 AH batteries.
CAB-4 Series: The ACPS-610(E) can mount in any of the

CAB-4 Series cabinets with

CHS-PS or CHS-BH

. See DN-

6857.
EQ Cabinet Series: The ACPS-610(E) can mount in any of

the EQ Cabinet Series cabinets using CHS-6. See DN-60229.
MARINE-EQ System: Protects equipment in shipboard and

waterfront applications. For a full list of required and optional

equipment, see DN-60688.

CHS-PS/

CHS-6: Chassis used to mount the ACPS-610(E) in

row 1, 2, or 3 of the CAB-4 or EQ series enclosure.
CHS-BH: Battery mounting chassis that holds up to two 12AH

batteries on a CHS-PS.
Batteries: ACPS-610(E) battery charging circuit range is 12 -

200 AH. See DN-6933.

Example of Programming

for the ACPS-610 Using 6 Addresses

0244

1.j

Example for ACPS-610

Using Canadian Reporting with Two Stage

244s

.jpg