Red Lion EPAX/MPAX - Manual (Page 4)

4
2.0 INSTALLING THE DISPLAY
EPAX DISPLAY INSTALLATION
The EPAX display is intended to be mounted
into a panel or enclosure. The display is provided
with a gasket to provide a water-tight seal. The
recommended minimum panel thickness for
NEMA 4/IP65 sealing is 0.060" (1.57 mm).
For panel mounting, prepare the panel
cut-out to the dimensions shown in
Figure 3. The supplied template may be
used to mark the cut-out and hole
locations on the panel. After the panel
cut-out has been deburred, slide the
panel gasket over the rear of the display
and onto the mounting studs. Insert the
display into the panel cut-out as
illustrated in Figure 4. Install 14 #
10-32 keps nuts (supplied) and tighten
evenly for uniform gasket compression.
Do not over-tighten the nuts.
By using additional mounting accessories,
the EPAX can be surface-wall mounted, suspended,
or bottom mounted. Separate installation instructions are
provided with the mounting accessories.
Environment And Cleaning
The display should be installed in a location that does
not exceed the maximum operating temperature and
provides good air circulation. Placing the system near
devices that generate excessive heat should be avoided.
The bezel should be cleaned only with a soft cloth and
neutral soap product. Do NOT use solvents. Continuous
exposure to direct sunlight may accelerate the aging
process of the bezel.
CAUTION
:
1
2
3
4
5
6
7
8
9
10
11
DISCONNECT AL
L
POWER BEFORE INSTALLING OR REMOVING MODULE
SLOT
TWIS
T
! WHILE FIRMLY DEPRESSING REAR FINGER TABS (TOP & BOTTOM), INSERT SCREWDRIVER BLADE (3/16" OR 1/4") INTO NARROW SLOT (AT THE ARROW) AND TWIST IN THE DIRECTION SHOWN
.
TO REMOVE MODULE
:
MODEL LPAX
RED LION CONTROLS YORK, PA. MADE IN U.S.A
.
PAXCDC1
0
RS485 COMMUNICATION 12 13 14
15
- B(-) - A(+)
- COMM - N/C
1
2
3
4
5
6
7
8
9
10
11
~~ AC
AC
85-250VAC 50/60H
z 14V
A
COMMUNICATION OPTION
ANALOG OUT OPTION
SETPOINT (SP) OPTION
MODEL PAXD
RED LION CONTROLS YORK, PA. MADE IN U.S.A.
SEE LITERATURE FO
R
JUMPER SELECTIO
N
SIGNAL INPUTS
USER INPUTS
VOLT/OH
M
CURRENT
+EXCITAT
ION
COMM 1
2
3
N/C
COMM
!
R
-
19
17
+ 18 -
+ 16 ANALOG OUTPUT
PAXCDL10
RLY3
25
21
RLY2
22
COMM RLY1
20 QUAD RELAY S.P
.
PAXCDS20
0-10
V ANALOG OUTPUT
OUTPUT ANALOG 0-20mA
24 23
COMM RLY4
RELAYS RATE
D
3A @ 250VA
C
(RESISTIVE LO
AD)
CAUTIO
N
DISCONNEC
T
ALL POWE
R
BEFOR
E
OPENING
MODULE
RETENTION
LATCH (TOP
AND BOTTOM)
MOUNTING
PANEL
PANEL
GASKET
FRONT
PANEL
MODULE RELEASE
FINGER TAB
(TOP & BOTTOM)
CASE
VENT
HOLES
REAR COVER PLATE
CONNECT THIS STUD
TO A PROTECTIVE
EARTHING SYSTEM
MOUNTING STUDS AND NUTS
(14 PLACES)
8 COMM RST KE
Y
7 F1 KE
Y F2 KE
Y
6 5
DSP KE
Y
PAR KE
Y
4 3
1 2
!
MODEL EPAX
MADE IN U.S.A
. RED LION CONTROLS YORK, PA.
RJ12
~ AC AC ~
85 - 250VA
C
50/60Hz @ 5V
A
CAUTION: DISCONNECT ALL POWER BEFORE INSTALL- ING OR REMOVING MODULE.
CONNECTE
D TO
MUST BE METAL PANE
L
MA22 04X E
!
Figure 4, Installing The EPAX Into A Panel
2X
(123.3)
5X 4.85
(158.2 )
(170.8)
6.72
6.23
3.36
(85.4)
0.23 (5.9) DIA.
THRU, TYP.
(604.3 )
23.79
24.27 (616.5)
+.04
-.00
+1.01
-.00
+.03
-.00
+.76
-.00
DIMENSIONS In inches (mm)
Figure 3, Panel Cut-out for the EPAX