Checkers Roadblocks 2512 Wheel Chocks User Guidelines - Manual (Page 2)

LIMITED WARRANTY: Checkers guarantees the products it manufactures or sells against defects in workmanship and material for a period of one (1) year
from the date of shipment or date of invoice, whichever is later. The product must be used, maintained and installed according to the instructions and
procedures provided, or this warranty is void. Any alteration or modification of the product will also void this warranty. CHECKERS’ OBLIGATION UNDER THIS
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS. No other warranty or remedy shall be provided. This warranty
specifically does not guarantee or cover payment or reimbursement of any damages or consequential damages beyond the above.
Any claim under this warranty must be made in writing within twelve (12) months of the date of shipment or the date of invoice, whichever is later. All products
returned to Checkers under this warranty must be prepaid. If it is determined that the product is defective in material and /or workmanship the repair or
replacement will occur, at Checkers’ option, at no charge and return freight prepaid by Checkers. All other return of product to the owner shall be at the
owner’s expense.
CHECKERS AND ITS AUTHORIZED AGENTS, EMPLOYEES AND REPRESENTATIVES SPECIFICALLY AND EXPRESSLY DISCLAIM ANY AND ALL OTHER
WARRANTIES, INCLUDING THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY OF MERCHANTABILITY WHICH
MIGHT OTHERWISE BE APPLICABLE UNDER ANY STATE OR FEDERAL LAW.
LIMITED LIABILITY OF CHECKERS: Checkers and its authorized agents, distributors and representatives do not guarantee the performance of any Checkers
product in the customer’s use as the manufacturer is unable to assure proper use by the customer. Proper use by the customer is necessary for the effectiveness
of the product, as well as the safety of those using same. The user is solely responsible to determine the suitability of any Checkers product for any intended use.
The user assumes all risk and liability for use of any Checkers product.
User specifically acknowledges receipt of proper instructions regarding the use of the product in the original packaging and disclaims any consequential
damages to person or property, damages for loss of use, lost time, loss of profit, lost income, loss of the Checkers’ product itself and/or other incidental or
consequential damages other than as warranted by Checkers limited warranty. User accepts the responsibility of removing from service any product that
becomes worn out, unusable, unfit for intended use or defective in any way such as to make the product a potential safety hazard. Checkers is unable to
undertake such obligations or responsibilities on behalf of the user as the user is in sole possession and control of the product.
© 2011 Checkers Industrial Safety Products
WARRANTY AND LIABILITY
www.checkersindustrial.com
620 COMPTON ST • BROOMFIELD, CO 80020 • PH: 720-890-1187 • FAX: 720-890-1191 • TOLL FREE: 800-438-9336
#ZIS-WRB2512
Ver: 2/11
INDUSTRIAL WHEEL CHOCKS
WHEEL CHOCK USER GUIDELINES
There are many considerations that must be taken into account before implementing chocking
procedures. If wheel chocks are expected to hold on a specific grade, then all of the variables that
may affect the chock’s performance must be taken into account:
A. Tire size
B. Tire Type (Pneumatic, Radial, Bias-Ply, Solid Rubber, etc.)
C. Gross vehicle weight
D. Varying tire pressures that naturally occur with changes in the environment
E. Type and condition of road surface (i.e. asphalt, gravel, dirt, firm, soft, wet, dry, icy, etc.)
You cannot simply test a pair of chocks with a specific vehicle and payload, and broadly assume
that the chocks will hold the same vehicle on the same grade every time. Countless combinations
of conditions exist and this must be considered when selecting the most appropriate wheel chock
for each application. Complete and thorough testing must be completed to ensure that specific
wheel chocks will meet your specific chocking requirements.
A variety of chocks should be tested to determine the best chock for your particular application.
2512 SERIES
WHEEL CHOCKS
FOR ALL INDUSTRIAL APPLICATIONS