GE PT925DNBB - Manual (Page 4)

4
Installation Instructions
Cutout for 30”
(76.2 cm)
Single Double
Wall Oven
A
Cabinet Width 30” (76.2 cm)
Recommended
Cutout Location
from Floor 26 1/2” (67.3 cm) Max.
Cutout Depth 23 1/2” (59.7 cm) Min.
Cutout Width 28 1/2” (72.4 cm) Min.
28 5/8” (72.7 cm) Max.
Cutout Height 27 1/4” (69.2 cm) Min.
27 5/16” (69.4 cm) Max.
These ovens are not approved for stackable
installations.
Side by Side Installations
Install two wall ovens in separate cutouts.
NOTE: If marks, blemishes or the cutout
opening are visible above the installed
oven, it may be necessary to add wood
shims under the runners and front trim
until the marks or opening are covered.
Caution:
Users may be burned when using an oven
mounted too high. The recommended
mounting height is based on a 5 ft tall
user.
NOTE: If the cabinet does not have
a front frame and the sides are less
than 3/4” (1.9 cm) thick, shim both
sides equally to establish the cutout
width.
CUTOUT
HEIGHT
27 1/4" MIN.
27 5/16" MAX.
CUTOUT
WIDTH
28 1/2" MIN.
28 5/8" MAX.
5"
22" TO
BOTTOM OF
JUNCTION BOX
JUNCTION B
LOCATION
RECOMMENDED
CUTOUT
LOCATION
32 1/2"
FROM THE
FLOOR
CABINET
WIDTH
30"
ALLOW 11/16" FOR
OVERLAP OF THE
OVEN OVER SIDE
EDGES OF CUTOUT
THE OPENING
BETWEEN INSIDE
WALLS MUST
BE AT LEAST
28 1/2"WIDE
ALLOW 1" FOR
OVERLAP
ON OVEN TOP
AND BOTTOM
OF CUTOUT
21"
ALLOW A MINIMUM
F 21" FOR CLEARANCE
ADJACENT CORNERS,
RAWERS, WALLS ETC.
N THE DOOR IS OPENED.
Allow 11/16”
(1.75 cm) for
overlap of oven
over side edges of
cutout
Cutout
Width
28 1/2”
(72.4 cm)
Min.
28 5/8”
(72.7 cm)
Max.
15”
(38.1 cm)
Cabinet
Width
30”
(76.2 cm)
Allow a minimum
of 15” (38.1 cm) for
clearance to adjacent
corners, drawers,
walls, etc. when
door is open
Allow 1” (2.5 cm)
minimum for
overlap of oven
top and 1 1/4”
(3.2 cm) overlap
of oven bottom
of cutout
Recommended
cutout
location from
fl oor 26 1/2”
(67.3 cm) max
Opening
Between
Inside Walls
Must Be
At Least
28 1/2”
(72.4 cm)
Wide
Junction Box
Location
(junction box
may be
located in adja-
cent cabinet)
9 1/2”
(12.7 cm)
Max.
Cutout
Height
27 1/4”
(69.2 cm) Min.
27 5/16”
(69.4 cm) Max.
22” (55.9 cm)
Min. to
Bottom of
Junction Box
If the cabinet does not have a solid bottom, two
braces or runners must be installed level with the
bottom of the cutout to support the weight of the
oven. For single ovens, the runners and braces
must support 200 lbs (91 Kg).
C L
T
2"
EQ
RU
21 5/8"
OVER CENTERLINE
OF CABINET
21 5/8”
(54.9 cm) Over
Centerline
of Cabinet
Cutout – observe all
dimensions and
requirements.
Center Line
30.5”
(77.5 cm)
Center Line
2” (5.1 cm) Min.
2” x 4”
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout
Suitable
Bracing
to Support
Runners
Cutout – observe all
dimensions and
requirements.