Canon imagePROGRAF iPF6450 User Manual
Basic guide
Table of contents
Document Outline
- Cover
- Preface
- Handling Paper
- Consumables and Maintenance
- Printer Parts
- Printer Relocation
- Software Installation
- Adjustments for Better Print Quality
- Troubleshooting
- Problems Regarding Paper
- Clearing Jammed Paper (Paper Feed Slot)
- Clearing Jammed Roll Paper
- Clearing a Jammed Sheet, Fed Manually
- Cut sheets cannot be pulled out from the front paper feed slot
- Roll paper cannot be inserted into the paper feed slot
- Cannot load sheets
- Paper is not cut neatly
- Paper is not cut
- Depression on the leading edge is left
- Margins are wide
- Printing does not start
- The printer stops during a print job
- Problems with the printing quality
- Printing is faint
- Paper rubs against the printhead
- The edges of the paper are dirty
- The surface of the paper is dirty
- The back side of the paper is dirty
- Roller marks are left across the trailing edge of paper
- Immediately after borderless printing, the trailing edge margin is soiled during regular printing
- Printed colors are inaccurate
- Banding in different colors occurs
- Colors in printed images are uneven
- Image edges are blurred or white banding occurs
- Setting the Blue Switch on the Platen
- The contrast becomes uneven during printing
- The length of printed images is inaccurate in the feeding direction
- Images are printed crooked
- Documents are printed in monochrome
- Line thickness is not uniform
- Lines or colors are misaligned
- Borders appear during borderless printing
- Spectrophotometer Trouble Shooting
- Cannot print over a network
- Installation problems
- Other problems
- Problems Regarding Paper
- Error Message
- Messages regarding paper
- Paper mismatch
- MediaType Mismatch
- The paper is too small.
- The paper is too small.
- PaprWidth Mismatch
- Paper size not detected.
- Insufficient paper for job
- This paper cannot be used.
- Roll printing is selected.
- Roll printing is selected, but manual paper is loaded.
- The roll is empty.
- Roll feed unit error.
- No Roll Unit.
- Manual printing is selected.
- Manual printing is selected, but a roll is loaded.
- Wrong paper feed slot for manual paper.
- Paper jam.
- Paper loaded askew.
- Paper not aligned with right guide.
- Cannot detect papr
- Cannot feed paper.
- Cannot cut paper.
- End of paper feed.
- Borderless printng not possible.
- Roll paper is not securely in contact with roll holder.
- Messages regarding ink
- Ink insufficient.
- No ink left.
- Remaining level of the ink cannot be correctly detected. Check ink tank.
- Cannot detect ink level correctly. Close tank cover.
- Close Ink Tank Cover
- Ink tank is empty.
- Not much ink is left.
- Check if ink tank is set, and its color and direction.
- The following ink tanks cannot be recognized.
- Do not pull out ink tank.
- Messages regarding printing or adjustment
- Cannot execute this command. Use other paper.
- Cannot print as specified.
- Cannot calibrate.
- Excessive temperature or humidity.
- Please execute common calibration.
- Please commn calibrt using above paper.
- Please calibrate using above paper.
- Before borderless printing, move the blue platen switch.
- Blue platen switch is dirty.
- Move the blue platen switch No.xx to the right. (xx represents a number)
- Cannot adjust paper feed.
- Check printed document.
- Spectrophotometer Unit not connected.
- Spectrophotometer Sensor not mounted.
- Spectrophotometer Unit Calibration white tile error.
- Spectrophotometer Unit eject guide not mounted.
- Spectrophotometer Unit Backing plate error.
- Spectrophotometer up-down unit cover open.
- Spectrophotometer Unit cover open.
- Spectrophotometer read error.
- Clean calibration white tile because it may be dirty.
- Messages regarding printheads
- Messages regarding the maintenance cartridge
- Messages regarding the hard disk
- Other Messages
- Error Messages
- Messages regarding paper
- Index