NORD Drivesystems TI 275271015 - Manual (Page 7)

PROFINET IO Bus module – SK CU4-PNT
TI 275271015 - 4913 7 / 8
Error messages
Error messages from the module - present errors or archived messages relating to the last error - can
be read out via the module parameter (P170). The error messages are lost if the module is switched
off.
Error Meaning Remarks
100.0 EEPROM error EMC fault, module defective
102.0 Timeout via P151/P513 monitoring
103.0 System bus BUS OFF No 24V supply to the bus, connections not correct
104.0 Module temperature too high only SK CU4-…, permissible internal temperature of the bus
module exceeded for approx. 60 sec
560.0 …
560.9 Internal error Module not ready
561.0 General network error
561.1 Ethernet Watchdog timeout
561.2 Bus cable fault Bus cable connection interrupted
561.3 IP address error IP address of the module has been doubly assigned
563.0 Firmware version incompatible The firmware version cannot be used for the device
564.0 MAC address error
Errors which occur in relation to the module are depicted as follows in the error memory of the
frequency inverter (P700 / P701).
Error
(E010) Meaning Remarks
10.0 Connection error Contact to SK xU4 lost
10.1 ASIC errors Communication to Ethernet - ASIC lost
• Switch-off of the supply voltage
• Reduce the temperature of the module (only SK CU4-…)
10.2 Ethernet Watchdog timeout Telegram transfer error
• Check the connections and links, program sequence and
Bus Master
10.3 Timeout by P151/P513 Telegram transfer error
• Check the connections and links
• Check the Watchdog time
10.4 IP address error IP address of the module has been doubly assigned
10.5 Internal error Module not ready for operation, configuration error
10.6 Bus cable fault Bus cable connection interrupted
10.8 The connection between the inverter
and the module had a timeout Only SK TU3 module
10.9 Module missing (P120) Only SK xU4 module
Pos : 27 /T echnisc he I nf ormati onen/ SK xU x - Bus - Erweit erungen/ Allgemei n - Syst emübergreifend/ Par ameter [SK xU x-. .. Allgemei n - Fr equenzumric ht er] @ 4\ mod_1384953855694_388.doc x @ 105781 @ 5 @ 1
Parameters
Frequency inverter: The following frequency inverter parameters must be adapted for setting up
communication between the frequency inverter and the bus module (for details see frequency
converter manual).
Parameter [-Array] Meaning Remarks
P120 [-01] Option monitoring "Auto“ (default setting) Only SK xU4
P509 Control word source SK TU3-… on SK 5xxE: "Ethernet TU”
SK xU4-… on SK 180/SK 2xxE: "System bus"
P510 [-01 … -02] Setpoint source "Auto“ (default setting)
P513 Time-out Monitoring of the SK TU3 bus module Only SK 5xxE
P543 [-01 …-03 (-05)]
and P543 … P545 Bus actual values (1 …3 (… 5)) Possible settings according to (P418)
P546 [-01 …-03 (-05)]
and P546 … P548 Bus target values (1 …3 (… 5)) Possible settings according to (P400)
P700 [-01] / P701 Current / last failures Information parameters
P740 / P741 Process data bus In / Out Information parameters
P745 Module version Information parameters Only SK TU3
P745 Module status Information parameters Only SK TU3
P748 CANopen / System bus status Information parameters
Pos : 28 /T echnisc he I nf ormati onen/ SK xU x - Bus - Erweit erungen/ PROF INET IO /Paramet er [ PNT Allgemei n] @ 4\ mod_1385367612358_388. doc x @ 106326 @ @ 1