NORD Drivesystems TI 275271006 - Manual (Page 5)

IO-Extension – SK CU4-IOE
TI 275271006 - 4912 5
Error messages
Error messages for the module - the present or archived messages for the last error - can be read out
via the module parameter (P170) (see Parameterisation).
Error Meaning Comments
1000 EEPROM error EMC fault, module defective
1030 System bus OFF No 24 V supply to bus, connections not correct
2000 DIP switch changed DIP switch configuration changed during operation
2001 DIP switch configuration incorrect Invalid DIP switch settings
2010 Error at analog output Overload, reference voltage, short-circuit, calibration error
2020 Inverter does not support the module Incorrect inverter type connected
Pos : 16 /T echnisc he I nf ormati onen/I O - Er weit er ung/ Par ametrierung [I O E Allgemein] @ 2\ mod_1352389903587_388.doc x @ 50978 @ 6 @ 1
Parameterisation
Inverter: In order to establish communication between the inverter and the IOE module, the following
inverter parameters must be changed.
Parameter Meaning Comments
(P514) Bus speed 5 (= 250 kBaud)
(P515 [-01]) Bus address FI 1 = 32 FI 2 = 34
FI 3 = 36 FI 4 = 38
(P480 [- 01 …-08]) DIN function of the device Possible settings according to (P420)
(P481 [- 05 …-08]) DOUT function of the device Possible settings according to (P434)
(P400 [- 03 …-06]) AIN function of the device Possible settings according to (P400)
(P418 [- 02 …-03]) AUT function of the device Possible settings according to (P418
IO extension: The module provides a selection of parameters for setting or displaying special
operating values. The parameters can be changed with the aid of the NORDCON software or with a
ParameterBox. Communication is only possible via an SK 54xE or SK 2xxE which is connected to the
module.
Parameter Meaning Comments
(P150) Set relays Set DOUT directly or control via BUS
(P152) Factory setting Reset the module parameters, calibrate AOUT
(P153 [- 01 …-02]) Minimum system bus cycle Reduction of bus load due to the module
(P160) Set analog output Set AOUT directly or control via BUS
(P161 [- 01 …-09]) Filter time Debounce or round input signals
(P162) Send broadcast Activate Broadcast mode (control of several
inverters by this module)
(P163) Invert analog output Invert analog signal
(P170 [- 01 … 02]) Present errors Display of module errors
(P171 [- 01 … 03]) Software version Firmware version / Revision
(P172) Configuration Module type
(P173) Module status Status of system bus or connected FI
(P174) Status of digital inputs Display of DIN switching status
(P175) Relay status Display of DOUT switching status
(P176 [- 01 … 03]) Actual voltage Voltage level of analog signals
Pos : 17 /T echnisc he I nf ormati onen/I O - Er weit er ung/ Weiterf ührende D okument ati onen und Soft ware [I OE Allgemein] @ 2\ mod_1352390057120_388. doc x @ 51003 @ 6 @ 1
Further documentation and software ( www.nord.com )
Document Name Document Meaning
NORD CON Parameterisation and diagnostic software BU 0200 SK 2xxE frequency inverter manual
BU 0000 Description of NORD CON software BU 0500 SK 5xxE frequency inverter manual
BU 0040 ParameterBox manual
=== Ende der List e f ür T ext mar ke I nhalt ===