SHIMPO DT-315AEB - Manual (Page 4)

LIMITED EXPRESS WARRANTY: Shimpo Instruments warrants, to the original purchaser of new products only, that this product shall be free from defects in workmanship and materials under normal use
and proper maintenance for one year from the date of original purchase. This warranty shall not be ef fective if the product has been subject to overload, misuse, negligence, or accident, or if the product has been
repaired or altered outside of Shimpo Instruments’s authorized control in any respect which in Shimpo Instruments’s judgment, adversely affects its condition or operation.
DISCLAIMER OF ALL OTHER WARRANTIES: The foregoing warranty constitutes the SOLE AND EXCLUSIVE WARRANTY, and Shimpo Instruments hereby disclaims all other warranties, expressed,
statutory or implied, applicable to the product, including, but not limited to all implied warranties of merchantability and fitness.
LIMITATION OF REMEDY: Under this warranty, Shimpo Instruments’s SOLE OBLIGATION SHALL BE TO REPAIR OR REPLACE the defective product or part, at Shimpo Instruments’ option. Shimpo
Instruments reserves the right to satisfy warranty obligation in full by reimbursing Buyer for all payments made to Shimpo Instruments, whereupon, title shall pass to Shimpo Instruments upon acceptance of return
goods. To obtain warranty service, Purchaser must obtain Shimpo Instruments’s authorization before returning the product, properly repackaged, freight pre-paid to Shimpo Instruments.
INDEMNIFICATION & LIMITATION OF DAMAGES: Buyer agrees to indemnify and hold Shimpo Instruments harmless from and against all claims and damages imposed upon or incurred arising, directly
or indirectly, from Buyer’s failure to perform or satisfy any of the terms described herein. In no event shall Shimpo Instruments be liable for injuries of any nature involving the product, including incidental or
consequential damages to person or property, any economic loss or loss of use.
MERGER CLAUSE: Any statements made by the Seller’s representative do not constitute warranties except to the extent that they also appear in writing. This writing constitutes the entire and final expression
of the parties’ agreement.
Warranty
Dimensions & Specifications
Troubleshooting
FPM reading is displayed but unit is not flashing:
• Flash tube may need to be replaced (see "Flash Tube
Replacement" section)
Stroboscope is in external trigger mode, no flash:
• Check flash tube. Replace if necessary
• Check for damaged wiring and/or loose pin connections
S T R O B O S C O P E S P E C I F I C A T I O N S
Model Model Model Model Model DT DT DT DT DT-315AEB -315AEB -315AEB -315AEB -315AEB
INTERNAL MODE INTERNAL MODE INTERNAL MODE INTERNAL MODE INTERNAL MODE
Flashing R
Flashing R Flashing R Flashing R Flashing Range ange ange ange ange 40.0 - 35,000 FPM (flashes per minute)
Accuracy Accuracy Accuracy Accuracy Accuracy ±0.01% of reading
R RR RResolution esolution esolution esolution esolution 0.1 FPM: 40.0 - 4,999.9 FPM
0.2 FPM: 5,000 - 7,999.8 FPM
0.5 FPM: 8,000 - 9,999.5 FPM
1 FPM: 10,000 - 35,000 FPM
Phase Shif Phase Shif Phase Shif Phase Shif Phase Shifttttt Use +/- push buttons (360° in 6 seconds)
Display Update Time Display Update Time Display Update Time Display Update Time Display Update Time 0.2 sec approx.
Output Signal Output Signal Output Signal Output Signal Output Signal Synchronous, 400 msec. Pulse output, 0 to +12 VDC amplitude(approx.), 4.7 K Ω impedance
R RR RRate Multiplier/Divider ate Multiplier/Divider ate Multiplier/Divider ate Multiplier/Divider ate Multiplier/Divider Multiply by 2, divide by 2
EXTERNAL MODE EXTERNAL MODE EXTERNAL MODE EXTERNAL MODE EXTERNAL MODE
Flashing R
Flashing R Flashing R Flashing R Flashing Range ange ange ange ange 0.0 - 35,000 FPM
Accuracy Accuracy Accuracy Accuracy Accuracy ±0.01% ±1 digit
Phase Shif Phase Shif Phase Shif Phase Shif Phase Shifttttt 0 - 359° with 1° resolution
Delay Time Delay Time Delay Time Delay Time Delay Time 0 - 2,000 msec from 40 - 10,000 FPM
Exter Exter Exter Exter Exter nal T nal T nal T nal T nal Trigger Input Signal rigger Input Signal rigger Input Signal rigger Input Signal rigger Input Signal LO level: 0 - 0.8 VDC, HI level: 2.5 - 12 VDC or open collector (NPN), pulse width 50 msec min.
Input Impedance Input Impedance Input Impedance Input Impedance Input Impedance 4.7 K Ω at 12 V / 6.8 K Ω at 0 V
GENER GENER GENER GENER GENERAL AL AL AL AL
Display Display Display Display Display 5 digits, 0.4" (10 mm) high, LED
Flash T Flash T Flash T Flash T Flash Tube P ube P ube P ube P ube Power/Life ower/Life ower/Life ower/Life ower/Life Xenon, 10 W max. (100 million flashes)
Flash Duration Flash Duration Flash Duration Flash Duration Flash Duration 10 - 40 msec
Sensor P Sensor P Sensor P Sensor P Sensor Power Supply ower Supply ower Supply ower Supply ower Supply 12 VDC (40 mA)
Low Batter Low Batter Low Batter Low Batter Low Batter y Indicator y Indicator y Indicator y Indicator y Indicator Display shows all L’s
PPPPPower R ower R ower R ower R ower Requirement equirement equirement equirement equirement Inter nal Battery Pack
Operating T Operating T Operating T Operating T Operating Temperature R emperature R emperature R emperature R emperature Range ange ange ange ange 32° - 104°F ( 0 - 40°C )
W W W W Weight eight eight eight eight 2.5 lb (1.1 kg)
Dimensions Dimensions Dimensions Dimensions Dimensions 7.28"L x 4.72"W x 4.72"H (185 mm x 120 mm x 120 mm)
W W W W War ar ar ar arranty ranty ranty ranty ranty 1 year
Standard Accessories Standard Accessories Standard Accessories Standard Accessories Standard Accessories Exter nal battery pack with charger
Optional Accessories Optional Accessories Optional Accessories Optional Accessories Optional Accessories Car rying case
Stroboscope is in internal trigger mode, no flash:
• Check flash tube. Replace if necessary
• Check for damaged wiring and/or loose pin connections