GW Instek GDS-1000-U Series Quick start guide - Manual (Page 2)

8. Press the Autoset key. A
square waveform will
appear in the center of the
display.
9. Press the Display key, then
Type and select the vector
waveform type.
10. Turn the adjustment point on the probe to flatten
the square waveform edge.
Over
Compensation Normal
Under
Compensation
11. Setting up the oscilloscope is complete. You may
start to use the oscilloscope.
S
PECIFICATIONS
The specifications apply when the oscilloscope is
powered on for at least 30 minutes under +20°C~+30°C.
Model Specific Specifications
GDS-1052-U
Bandwidth (–3dB)
DC coupling: DC ~ 50MHz
AC coupling: 10Hz ~ 50MHz
Bandwidth Limit 20MHz (−3dB)
Trigger Sensitivity 0.5div or 5mV (DC ~ 25MHz)
1.5div or 15mV
(25MHz~50MHz)
External Trigger
Sensitivity ~ 50mV (DC~25MHz)
~ 100mV (25MHz~50MHz)
Rise Time < 14ns approx.
GDS-1072-U
Bandwidth (–3dB)
DC coupling: DC ~ 70MHz
AC coupling: 10Hz ~ 70MHz
Bandwidth Limit 20MHz (−3dB)
Trigger Sensitivity 0.5div or 5mV (DC ~ 25MHz)
1.5div or 15mV
(25MHz~70MHz)
External Trigger
Sensitivity ~ 50mV (DC~25MHz)
~ 100mV (25MHz~70MHz)
Rise Time < 5.8ns approx.
GDS-1102-U
Bandwidth (–3dB)
DC coupling: DC ~ 100MHz
AC coupling: 10Hz ~
100MHz
Bandwidth Limit 20MHz (−3dB)
Trigger Sensitivity 0.5div or 5mV (DC ~ 25MHz)
1.5div or 15mV
(25MHz~100MHz)
External Trigger
Sensitivity ~ 50mV (DC~25MHz)
~ 100mV (25MHz~100MHz)
Rise Time < 3.5ns approx.
Common Specifications
Vertical
Sensitivity
2mV/div~10V/Div (1-2-5
increments)
Accuracy ± (3% x |Readout|+0.1div +
1mV)
Bandwidth See model-specific
specifications
Rise Time See model-specific
specifications
Input Coupling AC, DC, Ground
Input Impedance 1MΩ±2%, ~15pF
Polarity Normal, Invert
Maximum Input 300V (DC+AC peak), CAT II
Math Operation +, –, FFT
Offset Range 2mV/div~50mV/div: ±0.4V
100mV/div~500mV/div:
±4V
1V/div~5V/div: ±40V
10V/div : ±300V
Trigger
Sources
CH1, CH2, Line, EXT
Modes Auto, Normal, Single, TV,
Edge, Pulse
Coupling AC, DC, LF rej, HF rej, Noise
rej
Sensitivity See model-specific
specifications
External Trigger
Range
DC: ±15V, AC: ±2V
Sensitivity See model-specific
specifications
Input Impedance 1MΩ±2%, ~15pF
Maximum Input 300V (DC+AC peak), CATII
Horizontal
Range
1ns/div~50s/div, 1-2.5-5
increment
Roll: 50ms/div – 50s/div
Modes Main, Window, Window
Zoom, Roll, X-Y
Accuracy ±0.01%
Pre-Trigger 10 div maximum
Post-Trigger 1000 div
X-Y Mode
X-Axis Input
Channel 1
Y-Axis Input Channel 2
Phase Shift ±3° at 100kHz
Signal Acquisition
Real-Time
250M Sa/s maximum
Equivalent 25G Sa/s maximum
Vertical Resolution 8 bits
Record Length 4k points Maximum
Acquisition Normal, Peak Detect,
Average
Peak Detection 10ns (500ns/div ~ 50s/div)
Average 2, 4, 8, 16, 32, 64, 128, 256
Cursors and Measurement
Voltage
Vpp, Vamp, Vavg, Vrms,
Vhi, Vlo, Vmax, Vmin, Rise
Preshoot/ Overshoot, Fall
Preshoot/ Overshoot
Time Freq, Period, Rise Time, Fall
Time, + Width, – Width,
Duty Cycle
Cursors Voltage difference (ΔV) and
Time difference (ΔT) between
cursors
Auto Counter Resolution: 6 digits,
Accuracy: ±2%
Signal source: All available
trigger source except the
Video trigger
Control Panel Function
Autoset
Automatically adjust Vertical
Volt/div, Horizontal
Time/div, and Trigger level
Save/Recall Up to 15 sets of measurement
conditions and waveforms
Display
LCD
5.7 inch, TFT, brightness
adjustable
Resolution (dots) 234 (Vertical) x 320
(Horizontal)
Graticule 8 x 10 divisions
Display Contrast Adjustable
Interface
USB Slave Connector
USB1.1 & 2.0 full speed
compatible (flash disk not
supported)
USB Host connector Image (BMP) and waveform
data (CSV)
Probe Compensation Signal
Frequency range
1kHz ~ 100kHz adjustable,
1kHz step
Duty cycle 5% ~ 95% adjustable, 5% step
Amplitude 2Vpp±3%
Power Source
Line Voltage
100V~240V AC, 47Hz~63Hz
Power Consumption 18W, 40VA maximum
Fuse Rating 1A slow, 250V
Operation Environment
Storage Temperature
-20°C~70°C, no condensation
Relative humidity 80% @ 70°C
Dimensions and Weight
Dimensions
310(W) x 142(H) x 140(D) mm
Weight Approx. 2.5kg
Probe Specifications
GTP-070A-4 (GDS-1052-U, GDS-1072-U)
Probe Position
Position x10 Position x1
Attenuation Ratio 10:1 1:1
Bandwidth DC ~ 70MHz DC~6MHz
Input Resistance 10MΩ when
used with
1MΩ input
1MΩ when
used with
1MΩ input
Input Capacitance 28pF~32pF 120pF ~220pF
Maximum Input Voltage ≤600Vpk,
Derating with
frequency
≤200Vpk,
Derating with
frequency
Temperature –10°C ~ 50°C
Relative Humidity ≤85% @35°C
Safety Standard EN 61010-031 CAT II
GTP-100A-4 (GDS-1102-U)
Probe Position
Position x10 Position x1
Attenuation Ratio 10:1 1:1
Bandwidth DC ~ 100MHz DC~6MHz
Input Resistance 10MΩ when
used with
1MΩ input
1MΩ when
used with
1MΩ input
Input Capacitance 14.5~17.5pF
approx.
85~115pF
approx.
Maximum Input Voltage ≤600Vpk,
Derating with
frequency
≤200Vpk,
Derating with
frequency
Temperature –10°C ~ 50°C
Relative Humidity ≤85% @35°C
Safety Standard EN 61010-031 CAT II
Dimensions
VI D/ E MI T
VI D/ ST L O V
VI D/ ST L O V
U N E M
U N E M
2 H C
HT A M
1 H C
A cq uir e
Di sp la y
U tili ty
H elp
R un /S to p
VA
R IAB
LE
FO RC
E A uto se t
C urs or
S IN G LE
H ard cop y
M ea su re
S ave /R eca ll
LEVE
L
RE G GI RT
L AT N OZ I R O H
LA CI T RE V
CH
1
C AT 30 0V M 15 pF M AX . 3 00 Vp k
1
CH
2
EX T TR IG
C AT 30 0V M 15 pF M AX . 3 00 V pk
1
Y
X
310.
0
341.
5
142.0
162.3
115.
1
14
9.
0
159
.0
150
MH
z 1 G Sa /s
D igi ta l St orage
O sc illo sc op e
G D S-1 15 2A -U
EC Declaration of Conformity
We
GOOD WILL INSTRUMENT CO., LTD.
No.7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236,
Taiwan
GOOD WILL INSTRUMENT (SUZHOU) CO., LTD.
No. 69, Lushan Road, Suzhou New District Jiangsu, China
declares that the below mentioned product
GDS-1052-U, GDS-1072-U, GDS-1102-U
Are herewith confirmed to comply with the requirements set
out in the Council Directive on the Approximation of the Law
of Member States relating to Electromagnetic Compatibility
(2004/108/EC) and Low Voltage Equipment Directive
(2006/95/EC). For the evaluation regarding the
Electromagnetic Compatibility and Low Voltage Equipment
Directive, the following standards were applied:
◎ EMC
EN 61326-1 :
EN 61326-2-1: Electrical equipment for measurement, control and
laboratory use –– EMC requirements (2006)
Conducted and Radiated
Emissions
EN 55011: 2009+A1:2010 Electrostatic Discharge
EN 61000-4-2: 2009
Current Harmonic
EN 61000-3-2:
2006+A1:2009+A2:2009 Radiated Immunity
EN 61000-4-3:
2006+A1:2008+A2:2010
Voltage Fluctuation
EN 61000-3-2: 2008 Electrical Fast Transients
EN 61000-4-4: 2004+A1:2010
------------------------- Surge Immunity
EN 61000-4-5: 2006
-------------------------
Conducted Susceptibility
EN 61000-4-6: 2009
------------------------- Power Frequency Magnetic Field
EN 61000-4-8: 2010
------------------------- Voltage Dips/ InterruptsIEC
EN 61000-4-11: 2004
◎ Safety
Low Voltage Equipment Directive 2006/95/EC
Safety Requirements
IEC/EN 61010-1: 2001