Rane Serato Scratch Live - Manual (Page 2)

Introduction
Refer to the separate Quick Start guide that was included in the
box. If you lose yours, a new copy (along with this manual and all
other documentation) may be downloaded at
www.rane.com/mp4.html. To keep up with the latest tips, and
to check for software updates for your MP 4, visit the official
Scratch LIVE Forum at scratchlive.net
For the questions that the Quick Start guide doesn't answer,
please read through these operating instructions so you will know
how to get the most from your MP 4 and the included Scratch
LIVE software. Keep this manual in a safe place.
Minimum system requirements
• Computer with USB 1 port supporting Full Speed Mode (USB 1.1).
• Screen resolution 1024 x 768 or higher.
• Hard drive space for storing music.
• PC Windows XP with Service Pack 2 or Vista
(64-bit XP not supported)
Pentium 4 / 1.5 GHz
1 GB RAM.
• Mac OSX 10.3
G4 / 1 GHz
1 GB RAM.
Scratch LIVE is compatible with Intel-based Mac computers.
Note: no sound card is necessary.
Check List
These items are included with the MP 4 in the box:
• Scratch LIVE software install disc.
• 1 USB cable.
• IEC C5 line cord.
• Package of 4 rubber feet.
• Quick Start Guide.
• This manual.
Copyright notices
© 2007 Rane Corporation. All rights reserved. Scratch
LIVE and
the Scratch LIVE logo are trademarks of Serato Audio Research.
Trademarked in the U.S. and other countries. Licensed exclu-
sively to Rane Corporation. This software is based in part on the
work of the Independent JPEG Group, and uses libpng code,
copyright © 2000-2002 Glenn Randers-Pehrson. Control vinyl
and CDs are available for single use only — any further copying
or unauthorized reproduction is strictly prohibited. Windows
XP and Vista is either a registered trademark or a trademark of
Microsoft Corporation in the United States and/or other coun-
tries. Apple, Mac, Macintosh and iTunes are trademarks of Apple
Computer, Inc., registered in the US and/or other countries.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance
with manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or third prong is provided for
your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord and plug from being walked on or
pinched particularly at plugs, convenience receptacles, and the
point where it exits from the apparatus.
11. Only use attachments and accessories specified by Rane.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. The plug on the power cord is the AC mains disconnect
device and must remain readily operable.
16. This apparatus shall be connected to a mains socket outlet
with a protective earthing connection.
17. When permanently connected, an all-pole mains switch with
a contact separation of at least 3 mm in each pole shall be
incorporated in the electrical installation of the building.
18. If rackmounting, provide adequate ventilation. Equipment
may be located above or below this apparatus, but some
equipment (like large power amplifiers) may cause an
unacceptable amount of hum or may generate too much heat
and degrade the performance of this apparatus.
19. This apparatus may be installed in an industry standard
equipment rack. Use screws through all mounting holes to
provide the best support.
WARNING : To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. Apparatus shall not
be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
To reduce the risk of electrical shock, do not open the unit.
No user serviceable parts inside. Refer servicing to qualified
service personnel.
The symbols shown below are internationally accepted symbols that
warn of potential hazards with electrical products.
This symbol indicates that a dangerous voltage
constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
WARNING