Wellsaw 1316S-Auto - Manual (Page 2)

Specifi cations
Capacity
@ 0° (90°)
@ 45°
@ 60° Round | Rectangular
13" | 13"H x 16"W
12" | 13"H x 12"W
7-1/2" | 8-1/2"H x 7-1/2"W
Blade Size 1" x .035" x 12'6" (150")
Blade Speeds Infi nitely Variable 60-420 SFPM
Blade Guides Carbide Guides with Rollers
Blade Tension Double Die Spring with Indicator
Electrical Options 230/3 (See Options for Other Volt-
ages)
Coolant System Tank Capacity 8 Gallons
Submersible Pump 115V/.6 Amp/3
GPM
Vise Control Quick Positioning/Air Powered
Feed Rate Control Variable Positive Hydraulic with
Sawing Force Control
Cutting Force
Control 30-120 Lbs.
Jobs Storage 99
Band Wheels 15" Diameter Cast Iron
Barfeed Projection 25" Unlimited Indexes
Barfeed Accuracy +/- .002"
Barfeed Remnant 10"
Barfeed Length 5'
Weight Capacity 3,000 Lbs.
Bed Height 35"
Floor Area 90"W x 120"L
Shipping Weight 3,100 Lbs.
1316S-Auto Components
• Square D® Programmable Machine Controller with
Membrane Keypad and LCD display
• Square D® Vector Type Frequency Motor Controller
• Baldor® 5hp TEFC Blade Drive
• Baldor® 3/4hp Hydraulic Motor
• Textron/Cone Drive® Double Enveloping Gearbox
• Vickers® Hydraulic Valves
• Wellsaw Tiger-Tooth® Bi-Metal Blade
• Active Hydraulic Cutting Force Control
• Encoder Type Barfeed
• Blade Break/Stall Proximity Switch
• Working Light with Transformer
• Unitized Base Design (Saw and Barfeed) with Integral
Fork Pockets
• Out of Stock Shutdown
• Self Centering Shuttle Carriage with Anti-Climbing
Vises
• Discharge Table & Shute
• Spring-Loaded Carbide Guides with Rollers
• 8 Gallon Flood Coolants System with Sample/Start-Up
Coolant
• Full Surround Chip Pan
• Powered Blade Brush
• 110 Volts at Controls
• Overload and Undervoltage Protection
• Precision Ground Beds and Discharge Table
• Auto Shut-Off at End of Cut
• OSHA Blade Guarding
• Low Air Pressure Safety Switch
• NFPA Electrics (with Fused Disconnect)
• Flush Hose
Available Factory Options
Overhead/Bundle Clamping | Transformer for
460 Volt Operation | Chip Conveyor | Variable
Vise Pressure | Laser Line Pointer | 5' and 10'
Non-Powered Conveyors | Oil Injection Type
Lubrication Systems | Hour Meter
Key Features
Fully Automatic Bandsawing | Conversational
Set-Up | Encoder Type Barfeed | Quick Set-Up
and Multiple Job Programing | Automatic Kerf
Compensation | Machine Diagnostics | Hydraulic
Cutting Force Control System
Wellsaw® | 2829 N. Burdick Street | Kalamazoo, MI 49004 | Phone: 269-345-1132 | Fax: 269-345-0095 | Web: www.wellsaw.com
2
1316S-Auto Specifi cations ........................................2
1316S-Auto Components ..........................................2
Safety Instructions .....................................................3
Warranty Information .................................................5
Receiving and Installation..........................................5
Machine Overview .....................................................6
Trouble Shooting .......................................................8
Cutting Force Feature...............................................10 Auto Quick Start Guide .............................................12
Review of Control Panel Buttons & Operation..........13
The Six Control Screens...........................................15
Manual Operation .....................................................18
Automatic Operation .................................................18
Electrical Maintenance Notes ...................................19
General Operating Information .................................20
Blade Selection Guide ..............................................22
TABLE OF CONTENTS