Anthro Trolley Assembly Instructions - Manual (Page 2)

Trolley Cart
Anthro ® Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
Step 3
(requires the 6mm Hex Key)
Position both Trunk Assemblies and the 18” Lower Cross
Tube as shown.
Insert the 18” Cross Tube into the Large Holes of each
Trunk and loosely attach the Tube to each Trunk using one
Tube Screw per end.
NOTE: The 18” Cross Tube ends are keyed to fit into the Trunk
Assemblies.
NOTE: If you purchased a Trolley Base Shelf, install the Casters
to the Trunk Assemblies during this Step.
anthro.com
Step 5
(requires the 3-Way Wrench)
Position one Trolley Shelf & Handle Side against a Trunk
Assembly. Insert the two posts of a Side into holes 3 &
5 (from the top) of the Trunk. Loosely attach the Side to
the Trunk with one Button Head Screw and Keps Nut.
Repeat for the other Side.
Place the Trolley Handle between both Sides. Insert a
Handle Screw through both ends of the Side and carefully
thread into the Handle. Tighten the Button Head Screws
on the Sides.
NOTE: By installing the Side posts into holes 3 & 5, your final
Shelf height will be 36” from the floor.
Questions? 1-800-325-3841
Step 2
(requires the 3-Way Wrench)
STOP: If yOU PURCHASEd A TROllEy BASE SHElf,
REAd THOSE INSTRUCTIONS NOw.
Install all four Casters to both Trunk Assemblies using four
Button Head Screws per Caster.
DOUBLE CHECK THE INSTALLATION of the Swivel Lock
Casters (Green Brake Pedal) by positioning the Trunk Assembly
& Caster as shown. Then depress the Brake. If it is installed
correctly, the Caster will be locked in a parallel orientation (as
shown) with the Trunk Assembly.
NOTE: Make certain to install one Swivel Lock Caster (green brake)
and one Total Lock Caster (black brake) onto each
Trunk Assembly.
Step 4
(requires the 6mm Hex Key)
Rotate the Cart Assembly (from Step 3) onto the Casters.
Place the 12” Upper Cross Tube between each Trunk As-
sembly and align the Tube with the Large hole, midway
up the Trunk.
Carefully secure into place using one Tube Screw per end.
( 5 /
16
-18 X 1”) Tube Screw
325-5136-00
( 5 /
16
-18 X 3/4”) Button Head Screw
325-5188-00
( 1 /
4
-20 X .375”) Button Head
Screw
325-5210-00
( 1 /
4
-20) Keps Nut
325-5202-00
( 5 /
16
-18 X 1”) Tube Screw
325-5136-00
( 1 /
4
-20 X .375”) Button Head
Screw
325-5210-00
( 1 /
4
-20) Keps Nut
325-5202-00
( 1 /
4
-20 X 2”) Handle Screw
325-5034-00
Total lock Caster
(Black Brake Pedal)
front position
Swivel lock Caster
(green Brake Pedal)
rear position
Trunk Assembly (y)
Trunk Assembly (X)
keyed Cross Tube
ends
large hole
Shelf & Handle
Side (X)
Trolley Handle and Shelf & Handle Side (y)
are removed for clarity.
Hole 7
Hole 9
Shelf & Handle
Side (X)
Button
Head
Screw
keps Nut
Cable Hanger
Step 6
(requires the 3-Way Wrench)
Determine the location for your Trolley Cable Hangers,
then position one against a Trunk Assembly.
Insert two Button Head Screws through the Cable Hanger
and capture on the opposite side using two Keps Nuts.
Repeat for remaining Cable Hanger.
Step 1
BEFORE YOU BEGIN, take special notice of the features on
the Swivel Lock Casters (those with the Green Brake Pedals).
The teeth on the plate of both Swivel Lock Casters need to
face the rear of the Trunk Assemblies.
Step 2 will give further instructions about securing the
Casters to the Trunk Assemblies.
Teeth
(on the Plates) faces the rear
of the Trunk Assemblies Plate
Installed to the
Trunk Assemblies
NOTE: There are a matching
set of teeth on the truck.
Since the truck rotates, their
orientation is not critical.
Swivel lock Caster
(green Brake Pedal)
Rear of the Trunk
Assemblies
Truck
Trunk Assembly (y)
large hole
12” Cross Tube
Shelf & Handle
Side (y)
Handle Screw
Button Head Screw
keps Nut
Hole 3
Hole 5 Post