beautypg.com

Anthro Trolley Assembly Instructions User Manual

Trolley cart, Assembly instructions, Step 7a

background image

TECHNOLOGY FURNITURE

®

Trolley Cart

Assembly Instructions

01– Trolley Trunk Assembly (X) ... Qty. 1 .............................................
TR18zz/xx ...................................................................... 835-5018-00
TT18zz/xx ...................................................................... 835-5401-00
02– 5” Total Lock Casters

............ Qty. 2 ................. 150-5081-00

03–

5

/

16

-18 Button Head Screw

..... Qty. 16 ................ 325-5188-00

04–

5

/

16

-18 X 1” Tube Screws

....... Qty. 4 ................. 325-5136-00

05– 5” Swivel Lock Casters

......... Qty. 2 ................. 150-5080-00

06– Trolley Trunk Covers ................ Qty. 2 ............................................
TR18zz/xx ...................................................................... 225-5753-00
TT18zz/xx ...................................................................... 225-5278-00
07– 18.25” Lower Cross Tube ....... Qty. 1 ................... 125-5244-xx
08– Trolley Trunk Assembly (Y) .... Qty. 1 .............................................
TR18zz/xx ...................................................................... 835-5019-00
TT18zz/xx ...................................................................... 835-5402-00

09– 12” Upper Cross Tube

.......... Qty. 1 .................. 125-5243-00

10– Trolley Cable Wraps ................. Qty. 2 .................. 225-5756-00
11–

1

/

4

-20 Keps Nuts ........................ Qty. 6 .................. 325-5202-00

12– 18” Handle ................................. Qty. 1 .................. 125-5245-00
13– Shelf & Handle Side (X)

........ Qty. 1 .................. 225-5754-00

14– 18.5” Wide Trolley Shelf .......... Qty. 1 .................. 100-6495-00
15– Shelf & Handle Side (Y) ........... Qty. 1 .................. 225-5755-00
16–

3

/

4

” Wood Screws ...................... Qty. 6 .................. 325-5106-00

17–

1

/

4

-20 Button Head Screws

... Qty. 14 ................ 325-5210-00

18–

1

/

4

-20 X 2” Handle Screws

.... Qty. 2 .................. 325-5034-00

19– Non-Skid Pads

(not shown)

...... Qty. 8 .................. 175-5068-03

Hello!

Thank you for choosing Anthro.

Before beginning assembly of your

Trolley, please take a moment to

review the parts listed below to verify

that your shipment is complete.

All fastener quantities shown are the

minimum needed for this assembly.

There may be a few extras provided

which are not required.

Questions?

1-800-325-3841

Step 7a

Install Non-skid Pads on the top of the Trolley Trunk

Covers to cushion the edge of each Trunk Assembly

where it meets the cover. Install pads on the inside face

of the cover, at the edge, about 3.5” below the threaded

holes at the top of the cover.

The following Tools (not shown at right)

have been provided:

Hex Driver

5

/

32

” ...... 375-5000-00

Hex Key 6mm ......... 375-5013-00

3

/

16

” Allen Key .......... 375-5028-00

3-way Wrench ......... 225-5196-03

5/32” Driver Bit ..... 375-5003-00

Button Head Screws

Anthro

®

Corporation Technology Furniture

®

10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com

SAVE THESE INSTRUCTIONS!

November 2010, Rev H

1-800-325-3841

Trunk Cover

Step 8

STOP: If yOU PURCHASEd A SwINg OUT mOUSE SHElf

REAd THOSE INSTRUCTIONS BEfORE INSTAllINg THE

TOP.
Finally, place the main Trolley Shelf onto the installed

Shelf & Handle Sides, aligning the six holes on the

Shelf with those on the Sides.
Secure the Shelf to the Sides using a total of six

3

/

4

” Wood Screws. Tighten all Screws and Nuts.

Congratulations! Your assembly is complete!

3

/

4

” Wood Screw

325-5106-00

3

/

4

” wood Screws

into the six Trolley

Shelf holes

Step 7b

STOP: If yOU PURCHASEd A TROllEy

EqUIPmENT SHElf, AddITIONAl wOOd SHElf,

OR TROllEy TRAy REAd THOSE INSTRUCTIONS

BEfORE INSTAllINg THE TRUNk COVERS.
Install the Trolley Trunk Covers by orienting both Covers

with the Trunk Assemblies.
Secure the top and bottom of each Cover using a total of

four Button Head Screws per Cover.

Non-Skid Pad

175-5068-03

Threaded holes

Button Head

Screws

03

05

02

01

08

04

07

06

09

10

11

12

15

16

17

18

13

14

(

1

/

4

-20 X .375”) Button Head

Screw

325-5210-00

Component list for

part # TR18zz/xx and TT18zz/xx.

3.5”

Non-Skid Pads