Anthro CT Cart Spec Guide - Manual (Page 3)

CARL’S TABLE
24
Carl’
s
Table
CT08 ACCESSoRiES Model CT08 was available December, 2008, - November, 2012, and it’s still going strong.
To add options to your CT08 table, choose from this list. Not sure which table you have? Give us a call at 800.325.3995!
Cpu hoLdERS
• Add a second CPU to your Carl’s Table. Installs on the left or the right, opposite the CPU holder that comes with your Carl’s Table.
• All-metal holders move up and down with the table and integrate into the table’s safety system.
• Standard Holder has a weight capacity of 80 lbs. and CPUs 7-10"wide, 10-20" high.
• Super Holder has a weight capacity of 80 lbs. and CPUs 6.75"-8.5"wide, 17.5"-22" high, and up to 22" deep.
• Available in Silver Metallic (SM) only.
PRODUCT Weight Part # Price
CT CPU Holder - Standard 17 lbs. 367SM $349.95
CT CPU Holder - Super 42 lbs. 679SM $579.95
fLAT pAnEL moniToR ARm
• These steel arms have a vertical travel range of 16" and rotate 360 degrees. Travel range depends on the size of your monitor.
• Mount with either a C-clamp to the edge of your cart or drill through a shelf for added security. Clamp opens a maximum of 2" and
requires 3.5" of vertical clearance below the shelf.
• The Arms extend up to 22" from their mounting point.
• Ten-year warranty against manufacturing defects.
• The Standard and Super Arms are available in Black (BK) and Silver Metallic (SM). The Light Arm is available in Black (BK).
PRODUCT
Supports Monitors Weighing Weight Part # Price
Single - Standard 7.5-25 lbs. 20 lbs. LCDxx $239*
Single - Super 13.5-44 lbs. 20 lbs. LCD2xx $289*
Single - Light 2-13.5 lbs. 20 lbs. 770BK $269.95*
QuickShip available for Standard and Super arms.
KEyBoARd SuRfACE REpLACEmEnT pAd
• If needed, replace the pad on the keyboard surface with this pad. The cushioned, easy-clean material matches the contour of your Carl’s
Table keyboard surface.
PRODUCT Weight Part # Price
Pad 8 lbs. 475DG $299.95
moniToR ConTRoL SySTEm opTionS
• Customize your Carl’s Table CT08 with options to support and adjust your monitors. Even though CT08 is discontinued, you can still
update it as you change update your hardware!
• need to support a heavy diagnostic monitor, up to 55 lbs. Choose a mount to support it. Comes with a tray to support the transformer
brick. Installs at any position along the Monitor Control System.
• Add some extra width to your Monitor Control System with the Additional Monitor Bar. Your CT08 came with one Monitor Bar
Extension attached to the center boom. This accessory gives you an identical extension for the other side of the boom. Comes with a
standard knuckle and cable tray for the brick.
• Want to add more displays to your CT08? Add a Flat Panel Monitor Arm and attach it to the Coffee Surface. Perfect for RIS or voice
system monitors. Available in Black (BK) or Silver Metallic (SM).
PRODUCT Supports Monitors Weighing Weight Part # Price
Large Diagnostic Monitor Mount for CT08 Up to 55 lbs. 7 lbs. 691BK $359
Additional Monitor Bar for CT08 Up to 25 lbs. 9 lbs. 633BK $359
STAndARd
SupER
fLAT pAnEL
moniToR ARm
AddiTionAL ARm
foR CT08
AnThRo in ACTion
What better accessory for your
Carl’s Table than a Verte’ Chair?
Prices subject to change.
*Not available for discount.