Watlow Series SD - Manual (Page 4)

Wa t l o w S e r i e s S D C a l i b r a t i o n ■ 4 ■ F a c t o r y a n d C a l i b r a t i o n
Display Parameter Name
Description
Settings Range
(Integer values for Modbus
in parentheses.)
Default Modbus*
(less 40,001
offset)
Read/Write
Appears if:
[O;ty2]
[O.ty2]
Output 2 Type
Displays the hardware type for Output 2.
[nonE] none (0)
[~~DC]
DC/open collect. (1)
[rLAY] mech. relay (2)
[~SSr] solid-state relay (3)
[COM]
communications (5)
[nonE] (0) 203 R Always active.
[O;ty3]
[O.ty3]
Output 3 Type
Displays the hardware type for Output 3.
[nonE] none (0)
[~~DC] DC/open collect. (1)
[rLAY] mech. relay (2)
[~SSr] solid-state relay (3)
[Proc] process (4) [nonE] (0) 204 R Always active.
[`S;id]
[ S.id] Software ID
Displays the software ID number.
0 to 9999 NA 10 R Always active.
[S;UEr]
[S.VEr]
Software Version
Displays the firmware revision.
0.00 to 99.99 NA 11 R Always active.
[S;bLd]
[S.bLd]
Software Build Number
Displays the software build number.
0 to 9999 Build Number NA 13 R Always active.
[PWr]
[PWr]
Power Type
Displays the type of input power.
[~~AC] high voltage
[LOW] low voltage NA *NA Always active.
[`Sn-]
[ Sn-]
Serial Number 1
Displays the first four characters of the
serial number.
0 to 9999 NA 7, 8 R Always active.
[`Sn_]
[ Sn_-]
Serial Number 2
Displays the last four characters of the
serial number.
0 to 9999 NA 7, 8 R Always active.
[tc;50]
[tc.50]
Thermocouple, 50mV
Calibrate the thermocouple input to
50mV (see “Calibrating the Series SD”).
[``no]
[`yes] [``no] *NA Always active.
[tc;00]
[tc.00]
Thermocouple, 0mV
Calibrate the thermocouple input to 0mV
(see “Calibrating the Series SD”).
[``no]
[`yes] [``no] *NA Always active.
[tc;32]
[tc.32]
Thermocouple, 32°F
Calibrate the thermocouple input to 0°C
(32°F) (see “Calibrating the Series SD”).
[``no]
[`yes] [``no] *NA Always active.
[`r;15]
[ r.15]
RTD, 15 ohm
Calibrate the RTD input to 15 ohm (see
“Calibrating the Series SD”).
[``no]
[`yes] [``no] *NA Always active.
[r;380]
[r.380]
RTD, 380 ohm
Calibrate the RTD input to 380 ohms.
(see “Calibrating the Series SD”).
[``no]
[`yes] [``no] *NA Always active.
[``U;1]
[ v.1]
Input Calibrate, 1.0 Volt
Calibrate the process voltage input to 1.0
Volt (see “Calibrating the Series SD”).
[``no]
[`yes] [``no] *NA Always active.