Watlow Series 734 Data Communications - Manual (Page 23)

How to Use Data Communications
23
WATLOW Series 733/734
Index
A
Addr, 8
Address, 14
ALM, 17
ANSI X3.28 "=" Command, Fig. 8, 15
ANSI X3.28 "?" Command, Fig. 9, 16
ANSI X3.28 Protocol for EIA/TIA-422 & EIA/TIA-
485, 14
ASCII Character Set, Table 2, 9
ASCII Control Characters (Partial Set), Table 3, 9
A1HI, A2HI, 17
A1LO, A2LO, 17
AL1, AL2, 17
AUT1, AUT2, 17
B
bAUd, 8
Baud Rate, 8
C
C1, C2, 17
CAL1, CAL2, 17
Carriage Return, 11
CF, 8, 17
Command, "?" Example
ANSI X3.28, 16
XON/XOFF, 13
Command, "=" Example
ANSI X3.28, 15
XON/XOFF, 12
Command List, Table 5, 17-19
Communications
Prompts, 8
Switch Selection, 7
Wiring, 3
Connecting the Control and the Computer, 4-6, 7
CSP, 17
CT1, CT2, 17
D
dAtA, 8
Data Link Escape (DLE), 15
Data Rules, 10
Device Address, 8, 14
E
EIA/TIA-422, 3, 4
EIA/TIA-423, 3, 5
EIA/TIA-485, 3, 6
End of Text (ETX), 14
End of Transmission (EOT), 15
ER1, ER2, 18
Error Codes, 18, 20
Example Format, 11
F
Flow Control, 11
G
GB, 18
General Message Syntax, 10
H
Hardware Interface, 3, 7
HYS1, HYS2, 18
I
Identification Number, 14
INP1, INP2, 18
Interface Wiring,
EIA/TIA-422, Fig. 1, 4
EIA/TIA-423, Fig. 2, 5
EIA/TIA-485, Fig. 3, 6
L
LAT, 18
LOC, 18
LOOP, 18
M
MDL, 19
MDKY, 18
MENU, 19
Message Syntax, 10
MODE, 19
MS, 19
Multidrop, 3
N
NAKs and Error Codes, 20
Network Connections, 7
P
PB1, PB2, 19
Prot, 8
Protocol
ANSI X3.28, 3, 7
XON-XOFF, 3, 7
Switches, 7
R
RA1, RA2, 19
RE1, RE2, 19
RH1, RH2, 19
RL1, RL2, 19
RTD, 19
RUN, 19
S
Serial Interface, 7
Setup Menu, 8
SIL, 19
Software Protocols, 3, 8
Space, 11
Starting Communications in ANSI X3.28 Protocol, 14
Start of Text (STX), 14
STAT, 19
STOP, 19
STP, 19
Stopping Communications in ANSI X3.28 Protocol, 15
Switches, Hardware Protocol, 7
T
TCMP, 19
TREM, 19
TS, 19
Two Hardware Interfaces & Protocols, 3
W
Wiring for Data Communications, 4-6
X
XON/XOFF
"=" Command Example, Fig. 6, 12
"?" Command Example, Fig. 7, 13
Protocol, 3, 7
Protocol for EIA/TIA-423, 13
Switches, 7